Midcity SmartKey starter - Revision history

Pokseva: /* Operation */

2017-04-29T17:15:59Z

Operation

← Older revision		Revision as of 17:15, 29 April 2017
Line 91:		Line 91:
	The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.		The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.

	For vehicles equipped with [[KEYLESS-GO]] function, press the KEYLESS-GO ~~"START"~~ button once without depressing brake pedal.		For vehicles equipped with [[KEYLESS-GO]] function, press the KEYLESS-GO push start button once without depressing brake pedal.
	The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.		The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.
	The vehicle security system remains intact while the engine is remote started.		The vehicle security system remains intact while the engine is remote started.
	The [[KEYLESS-GO]] and [[SmartKey]] locking and unlocking will still function and the gear shift will remain locked until either a valid key is inserted into the ignition or the ~~"START"~~ button is pressed while a valid key is present in the vehicle.		The [[KEYLESS-GO]] and [[SmartKey]] locking and unlocking will still function and the gear shift will remain locked until either a valid key is inserted into the ignition or the push start button is pressed while a valid key is present in the vehicle.
	If the footbrake is depressed or the hood is opened while remote started, the engine will immediately shut down.		If the footbrake is depressed or the hood is opened while remote started, the engine will immediately shut down.

Pokseva: /* Troubleshooting */

2017-04-29T17:14:54Z

Troubleshooting

← Older revision		Revision as of 17:14, 29 April 2017
Line 135:		Line 135:
	* 10 flashes - communication error		* 10 flashes - communication error

	If any problems are encountered, the remote starter system can always be reset using the ~~folowing~~ procedure:		If any problems are encountered, the remote starter system can always be reset disconnecting connector from SmartKey starter module or using the following procedure:
	# Turn of ignition		# Turn of ignition
	# Lock the car		# Lock the car

Pokseva: /* Valet Mode */

2017-04-29T17:14:01Z

Valet Mode

← Older revision		Revision as of 17:14, 29 April 2017
Line 109:		Line 109:
	Note: When the system has been placed in valet mode, it is necessary to re-initialize the starter system		Note: When the system has been placed in valet mode, it is necessary to re-initialize the starter system
	before the vehicle can be remote started again. To reinitialize the system, first turn off valet mode and		before the vehicle can be remote started again. To reinitialize the system, first turn off valet mode and
	then simply start the vehicle with either the key or using the [[KEYLESS-GO]] ~~Push Start Button~~ and allow the		then simply start the vehicle with either the key or using the [[KEYLESS-GO]] push start button and allow the
	vehicle to run for one (1) minute. The vehicle can now be remote started.		vehicle to run for one (1) minute. The vehicle can now be remote started.

	== Non-panic Button Activation ==		== Non-panic Button Activation ==

Pokseva: /* Operation */

2017-04-29T17:13:24Z

Operation

← Older revision		Revision as of 17:13, 29 April 2017
Line 91:		Line 91:
	The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.		The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.

	For vehicles equipped with [[KEYLESS-GO]] function, press the KEYLESS-GO "START" button once.		For vehicles equipped with [[KEYLESS-GO]] function, press the KEYLESS-GO "START" button once without depressing brake pedal.
	The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.		The parking lights will flash three times to indicate that the Smartkey starter has shut down but the engine will remain running.
	The vehicle security system remains intact while the engine is remote started.		The vehicle security system remains intact while the engine is remote started.
	The ~~KeylessGo~~ and ~~keyfob~~ locking and unlocking will still function and the gear shift will remain locked until either a valid key is inserted into the ignition or the ~~‘START’~~ button is pressed while a valid key is present in the vehicle.		The [[KEYLESS-GO]] and [[SmartKey]] locking and unlocking will still function and the gear shift will remain locked until either a valid key is inserted into the ignition or the "START" button is pressed while a valid key is present in the vehicle.
	If the footbrake is depressed or the hood is opened while remote started, the engine will immediately shut down.		If the footbrake is depressed or the hood is opened while remote started, the engine will immediately shut down.

	== Valet Mode ==		== Valet Mode ==

Pokseva: /* Installation */

2017-04-29T17:08:44Z

Installation

← Older revision		Revision as of 17:08, 29 April 2017
Line 37:		Line 37:
	and tie up all harnessing neatly and away from any heat source or moving parts.		and tie up all harnessing neatly and away from any heat source or moving parts.

	In case of W220, starter module together with relays can be ~~let down in instrument panel on the~~ right from steering column (behind [[EIS]]).		In case of W220, remote starter module together with relays can be installed behind dashboard, right from steering column (behind [[EIS]]).

	==KEYLESS-GO Connection==		==KEYLESS-GO Connection==

Pokseva: /* Known Issues */

2017-04-29T17:04:08Z

Known Issues

← Older revision		Revision as of 17:04, 29 April 2017
Line 143:		Line 143:
	# Wait 1 minute		# Wait 1 minute
	# Turn off ignition		# Turn off ignition

			==Known Issues==

			* [[Trunk]] cannot be opened using [[SmartKey]] if vehicle is started using remote starter.
			* If [[Exterior mirrors\|exterior mirror]] "fold-in when locking" feature is activated, the mirrors will not completely fold out if vehicle is started using remote starter.

Pokseva: /* KEYLESS-GO Connection */

2017-04-29T16:59:27Z

KEYLESS-GO Connection

@@ Line 47: / Line 47: @@
 Instructions:
-# Locate the CAN distribution block that houses the KeylessGo connector.
+# [[Removing and installing front floor covering (right)|Remove front floor covering from the passenger side.]]
-# Remove all connectors from the block that contain brown and brown/red twisted wires.
+# Open cover of wiring panel to access CAN distribution block.
-# Locate the KEYLESS-GO module and unplug the KEYLESS-GO module.
+# Remove CAN block cover in order to be able to disconnect plugs.
-# Unclip and remove the connector cover from the KEYLESS-GO connector.
+# Insert [[SmartKey]] in [[EIS]]. Turn the key to accessory (one click clockwise from the off position).
 # Look inside the Smartkey Starter® module through the end plate opposite the main wiring plug. You should see red LEDs that are lit up. One of those should be flashing at a slow pace.
-# In the CAN distribution block, begin to remove connectors one at a time. Each connector should be unplugged for 15-20 seconds each. Observe the flashing light as you do this. You should end up with two connectors that cause the flashing light to stop flashing and stay solid on or solid off.
+# In the CAN distribution block, begin to remove connectors one at a time. Each connector should be unplugged for 15-20 seconds. Observe the flashing light as you do this. You should end up with two connectors that cause the flashing light to stop flashing and stay solid on or solid off.
 # Isolate those two connectors to one end of the distribution block and leave the rest alone.
 # Turn the key to the off position and remove it.
-# Take the two connectors from step 5 and remove one at a time. Once one is removed, use the keyfob to unlock the doors. Removing one of those connectors will cause the door locks to stop working from the keyfob and one won’t.
+# Take the two connectors found and remove one at a time. Once one is removed, use the [[SmartKey]] to unlock the doors. Removing one of those connectors will cause the door locks to stop working and one won't. The one which keeps door locks continuing to work is the plug that has to be connected to KEYLESS-GO harness.
-# Take the connector that caused the door locks to stop working and plug it back in.
+# Before connecting the plug to KEYLESS-GO harness, remove the connector and swap the pins.
-# Connect the KeylessGo harness to the plug from step 7 where the door locks continued to work.
+# Secure the connection in wiring panel.
 == Operation ==

Pokseva: /* Installation */ note about starter module placement

2017-04-29T15:59:48Z

Installation: note about starter module placement

← Older revision		Revision as of 15:59, 29 April 2017
Line 32:		Line 32:
	{\|		{\|
	\|[[File:W220_SmartKey_starter_installation_module_connected.jpg\|thumb\|none\|Connect SmartKey starter module.]]		\|[[File:W220_SmartKey_starter_installation_module_connected.jpg\|thumb\|none\|Connect SmartKey starter module.]]
	~~\|[[File:W220_SmartKey_starter_installation_module_on.jpg\|thumb\|none\|Test if SmartKey starting works.]]~~
	\|}		\|}

	Mount the Smartkey starter module securely in the dash cavity away from any heat source		Mount the Smartkey starter module securely in the dash cavity away from any heat source
	and tie up all harnessing neatly and away from any heat source or moving parts.		and tie up all harnessing neatly and away from any heat source or moving parts.

			In case of W220, starter module together with relays can be let down in instrument panel on the right from steering column (behind [[EIS]]).

	==KEYLESS-GO Connection==		==KEYLESS-GO Connection==

Pokseva: /* KEYLESS-GO Connection */

2017-04-26T14:05:20Z

KEYLESS-GO Connection

← Older revision		Revision as of 14:05, 26 April 2017
Line 65:		Line 65:
	the Smartkey Starter® needs to be completed prior to testing for KeylessGo (this guide assumes the starter module is installed		the Smartkey Starter® needs to be completed prior to testing for KeylessGo (this guide assumes the starter module is installed
	and properly working).		and properly working).

	Instructions		Instructions
	# Locate the specified CAN distribution block where the KeylessGo connection should be made.		# Locate the specified CAN distribution block where the KeylessGo connection should be made.

Pokseva: /* KEYLESS-GO Connection */

2017-04-26T14:03:28Z

KEYLESS-GO Connection

← Older revision		Revision as of 14:03, 26 April 2017
Line 39:		Line 39:

	==KEYLESS-GO Connection==		==KEYLESS-GO Connection==
	In order to activate [[KEYLESS-GO]] vehicle ~~entry during~~ remote ~~start~~,		In order to activate [[KEYLESS-GO]] vehicle opening when the vehicle has been started using remote starting,
	an extra harness will have to be run to a separate CAN connector in the vehicle.		an extra harness will have to be run to a separate CAN connector in the vehicle.