Rear axle - Revision history

Pokseva: /* Replace differential fluid */

2023-09-05T15:39:30Z

Replace differential fluid

← Older revision		Revision as of 15:39, 5 September 2023
Line 314:		Line 314:

	This video shows all the tools and parts needed to replace the differential fluid on a W220 model along with torque specs.		This video shows all the tools and parts needed to replace the differential fluid on a W220 model along with torque specs.

			Tools required:
			* Hex socket 14mm
			* ~1.6 liters of axle drive oil according to MB 235.7 spec (SWAG 10948785 75W-85 1L x2)

			{\|
			\|[[File:14mm-hex-socket-bit-1-2.jpg\|thumb\|none\|14mm hex socket bit 1/2]]
			\|[[File:SWAG_10948785.jpg\|thumb\|none\|SWAG 10948785 75W-85 1L]]
			\|}

			Procedure:
			# Raise the car making sure that it is even on both axles
			# Unscrew the upper 14mm hex screw
			# Unscrew the lower 14mm hex screw
			# Let the old oil drip in a pan
			# Screw-in the lower 14mm hex screw
			# Pour the new oil via the upper screw hole until the differential is full and the oil starts to drip from the upper hole
			# Screw-in the upper 14mm hex screw

			{\|
			\|[[File:W220_rear_differential_unscrewing_upper_screw.jpg\|thumb\|none\|Unscrewing upper screw]]
			\|[[File:W220_rear_differential_pouring_new_oil.jpg\|thumb\|none\|Pouring new oil]]
			\|}

	= Shaft =		= Shaft =

2023-09-05T15:14:51Z

Differential: Replace differential fluid

← Older revision		Revision as of 15:14, 5 September 2023
Line 307:		Line 307:
	\|[[File:W220_rear_axle_with_housing_differential2.png\|thumb\|none\|]]		\|[[File:W220_rear_axle_with_housing_differential2.png\|thumb\|none\|]]
	\|}		\|}

			==Replace differential fluid==
			{\|
			\|{{#ev:youtube\|https://youtu.be/Lel6losmMX0\|320\|center\|Mercedes W220 S500 and S430 Differential Fluid Replacement (By Masood)\|frame}}
			\|}

			This video shows all the tools and parts needed to replace the differential fluid on a W220 model along with torque specs.

	= Shaft =		= Shaft =

2023-08-08T11:56:36Z

Remove/install spring control arm and replacement of rubber mount: photos and instructions added

@@ Line 286: / Line 286: @@
 [[File:W220_install_spring_control_arm_rubber_mount.jpg|500px]]
 [[File:W220_install_spring_control_arm_rubber_mount_2.jpg|300px]]
 = Differential =

2023-02-23T16:47:25Z

Replace rubber mounts of rear shock absorbers

@@ Line 157: / Line 157: @@
 * Using the thrust piece part 01 (06a) draw in the supporting joint until it abuts the machined contact surface (arrow). The supporting joint has been properly inserted when it is in the center of the wheel carrier boss.
 |}
 {|
@@ Line 165: / Line 164: @@
 |{{#ev:youtube|https://www.youtube.com/watch?v=HrlkBoK--E4|320|left|Squeaking joint at rear wheel carrier|frame}}
 |}
 = Torsion bar =
@@ Line 383: / Line 424: @@
 # Adjust vehicle road height with Star SDS.
 # Get rear wheels aligned.
 ==Resources - Rear Suspension==

2021-09-25T06:45:05Z

Remove/install supporting joint at wheel carrier (wheel carrier installed): photo and video added

← Older revision		Revision as of 06:45, 25 September 2021
Line 113:		Line 113:

	== Remove/install supporting joint at wheel carrier (wheel carrier installed) ==		== Remove/install supporting joint at wheel carrier (wheel carrier installed) ==

			''A failed rubber of supporting joint at wheel carrier is a common cause for a squeaking rear suspension.''
	<!-- AR35.20-P-0116I, Remove/install supporting joint at wheel carrier (wheel carrier installed), 27.9.97		<!-- AR35.20-P-0116I, Remove/install supporting joint at wheel carrier (wheel carrier installed), 27.9.97
	MODELS 215.373 /374 /375 /376 /378 /379, 220.025 /026 /028 /063 /065 /067 /073 /074 /070 /075 /083 /084 /087 /125 /126 /128 /165		MODELS 215.373 /374 /375 /376 /378 /379, 220.025 /026 /028 /063 /065 /067 /073 /074 /070 /075 /083 /084 /087 /125 /126 /128 /165
Line 160:		Line 162:
	\|[[File:W202589004300.jpg\|thumb\|none\|[[Special tools\|Special tool]] W202589004300]]		\|[[File:W202589004300.jpg\|thumb\|none\|[[Special tools\|Special tool]] W202589004300]]
	\|[[File:A2203520027_TRW_JBU167.jpg\|thumb\|none\|Supporting joint A2203520027]]		\|[[File:A2203520027_TRW_JBU167.jpg\|thumb\|none\|Supporting joint A2203520027]]
			\|[[File:W220_rear_right_wheel_carrier_rubber_joint_installed.jpg\|thumb\|none\|Supporting joint installed]]
			\|{{#ev:youtube\|https://www.youtube.com/watch?v=HrlkBoK--E4\|320\|left\|Squeaking joint at rear wheel carrier\|frame}}
	\|}		\|}

2021-09-03T00:39:37Z

Remove/install supporting joint at wheel carrier (wheel carrier installed): explanation on how to lower spring control arm

← Older revision		Revision as of 00:39, 3 September 2021
Line 127:		Line 127:

	# Remove rear wheels		# Remove rear wheels
	# Remove spring link (6)		# Remove spring link (6). ''In practice, it is sufficient to lower spring control arm by removing bolt to wheel carrier (21mm and E18) and removing stabilizer bar link bottom nut (16mm) and detach the bottom part of the stabilizer bar.''
	# Remove supporting joint (7a) from wheel carrier (7)		# Remove supporting joint (7a) from wheel carrier (7)
	# Install in the reverse order		# Install in the reverse order

2021-09-02T19:26:28Z

Remove/install spring control arm and replacement of rubber mount

@@ Line 182: / Line 182: @@
 |Control arm bearing, Spring link to rear axle bracket (left and right)
 |}
 = Differential =

2021-09-02T19:01:53Z

Remove/install supporting joint on wheel carrier: added photos

← Older revision		Revision as of 19:01, 2 September 2021
Line 154:		Line 154:
	\|Shown on model 220 with AIRMATIC		\|Shown on model 220 with AIRMATIC
	* Using the thrust piece part 01 (06a) draw in the supporting joint until it abuts the machined contact surface (arrow). The supporting joint has been properly inserted when it is in the center of the wheel carrier boss.		* Using the thrust piece part 01 (06a) draw in the supporting joint until it abuts the machined contact surface (arrow). The supporting joint has been properly inserted when it is in the center of the wheel carrier boss.
			\|}


			{\|
			\|[[File:W202589004300.jpg\|thumb\|none\|[[Special tools\|Special tool]] W202589004300]]
			\|[[File:A2203520027_TRW_JBU167.jpg\|thumb\|none\|Supporting joint A2203520027]]
	\|}		\|}

2021-09-02T18:58:43Z

Remove/install supporting joint at wheel carrier (wheel carrier installed)

@@ Line 110: / Line 110: @@
 {|
 |{{#ev:youtube|https://www.youtube.com/watch?v=b0Bb49lfcAg|320|left|Replacing rear right thrust arm|frame}}
 |}

2021-08-29T13:08:30Z

Suspension

← Older revision		Revision as of 13:08, 29 August 2021
Line 58:		Line 58:
	\|A2203520027		\|A2203520027

	TRW JBU167		Lemförder 2099402 (20 EUR)

			TRW JBU167 (20 EUR)
	\|[[File:A2203520027_TRW_JBU167.jpg\|300px]]		\|[[File:A2203520027_TRW_JBU167.jpg\|300px]]
	\|Supporting joint (left and right)		\|Supporting joint (left and right)