Pneumatic System Equipment (PSE): Difference between revisions
Jump to navigation
Jump to search
(Created page with "==Removing and installing PSE control module== <!-- AR80.20-P-2700M, MODEL 215, 220, Removing and installing PSE control module (A37/2-A37/5), 8.4.98 --> {| |File:W220_Remo...") |
(DAS adaptations) |
||
| Line 22: | Line 22: | ||
{| | {| | ||
|{{#ev:youtube|https://www.youtube.com/watch?v=J3Hs9UzwdLY|320|left|Removing vacuum pump.|frame}} | |{{#ev:youtube|https://www.youtube.com/watch?v=J3Hs9UzwdLY|320|left|Removing vacuum pump.|frame}} | ||
|} | |||
==DAS adaptations== | |||
Adaptations available in DAS for PSE control unit (A2208001248). | |||
{| | |||
|[[File:W220_PSE_adaptations_menu.png|thumb|none|Adaptations menu.]] | |||
|[[File:W220_PSE_adaptations_list.png|thumb|none|List of adaptations.]] | |||
|[[File:W220_PSE_adaptation_trunk_lid_remote_release.png|thumb|none|Trunl lid remote release.]] | |||
|} | |||
{| | |||
|[[File:W220_PSE_adaptation_trunk_lid_remote_closing.png|thumb|none|Trunk lid remote closing.]] | |||
|[[File:W220_PSE_adaptation_trunk_interior_button.png|thumb|none|Trunk interior button.]] | |||
|[[File:W220_PSE_adaptation_head_restraint_adjustment.png|thumb|none|Head retraint adjustment.]] | |||
|} | |||
{| | |||
|[[File:W220_PSE_adaptation_multicontour_backrests.png|thumb|none|Multicontour backrests.]] | |||
|[[File:W220_PSE_adaptation_central_locking.png|thumb|none|Central locking.]] | |||
|[[File:W220_PSE_adaptation_power_locking.png|thumb|none|Power locking.]] | |||
|} | |||
{| | |||
|[[File:W220_PSE_adaptation_childproof_locks.png|thumb|none|Childproof locks.]] | |||
|[[File:W220_PSE_adaptation_emergency_opening.png|thumb|none|Emergency opening.]] | |||
|[[File:W220_PSE_factory_settings_trunk_lid_remote_closing.png|thumb|none|Factory settings trunk lid remote closing.]] | |||
|} | |} | ||
Revision as of 14:12, 25 February 2017
Removing and installing PSE control module
|
|
- Remove paneling in trunk (except right side paneling and rear wall paneling)
- Press apart plastic lugs (arrows) and remove foam cap (1)
- Unclip pneumatic strips (2, 3) on pneumatic control module with PSE control module (combined) (A37). Clips are located in the oblong holes marked with arrows. Unclip with flat tool, e.g. screwdriver.
- Loosen electrical connector (4) on PSE control module (combined) (A37) and remove lead. Turn in direction of arrow.
- Remove PSE control module (combined) (A37).
- Install in opposite order. If the PSE is replaced version coding must be accomplished via STAR DIAGNOSIS.
- Check central locking, lumbar support or multicontour backrest, power locking, head restraint extension and retraction for proper function.
DAS adaptations
Adaptations available in DAS for PSE control unit (A2208001248).
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |