WIS 88.50 Trunk/Boot Lid: Difference between revisions
(→Trunk lid covering: U.S version A2207500381) |
|||
| Line 58: | Line 58: | ||
=== Facelift === | === Facelift === | ||
Facelift vehicles (From Date: 30/09/2002) have lid covering A2207500281 | Facelift vehicles (From Date: 30/09/2002) have lid covering A2207500281 | ||
which is attached to the lid with one | which is attached to the lid with one bolt in center tightened from inside and 8 retaining clips. | ||
The covering has also different trunk lid handle opening modified for retractable trunk lid grip. | The covering has also different trunk lid handle opening modified for retractable trunk lid grip. | ||
| Line 64: | Line 64: | ||
|[[File:W220_trunk_lid_covering_A2207500281_facelift_front.jpg|thumb|none|Trunk lid covering A2207500281 (facelift) front.]] | |[[File:W220_trunk_lid_covering_A2207500281_facelift_front.jpg|thumb|none|Trunk lid covering A2207500281 (facelift) front.]] | ||
|[[File:W220_trunk_lid_covering_A2207500281_facelift_back.jpg|thumb|none|Trunk lid covering A2207500281 (facelift) back.]] | |[[File:W220_trunk_lid_covering_A2207500281_facelift_back.jpg|thumb|none|Trunk lid covering A2207500281 (facelift) back.]] | ||
|[[File:W220_trunk_lid_covering_facelift_bolt.jpg|thumb|none|Bolt tightening covering to the trunk lid.]] | |||
|} | |} | ||
Revision as of 00:47, 15 February 2016
Components
|
|
|
|
|
|
Trunk lid covering
There are differences between pre-facelift and facelift vehicles in how trunk lid covering attached to the trunk lid.
Pre-facelift
Pre-facelift vehicles (To Date: 01/09/2002) have lid covering A2207500081 which is attached to the lid with two screws in center tightened from outside and 7 screws tightened from inside.
 |
 |
Facelift
Facelift vehicles (From Date: 30/09/2002) have lid covering A2207500281 which is attached to the lid with one bolt in center tightened from inside and 8 retaining clips. The covering has also different trunk lid handle opening modified for retractable trunk lid grip.
 |
 |
 |
The U.S. version A2207500381 has smaller distance between licence plate mounting holes.
 |
 |
Description - Trunk/Boot Lid
The S-Class Trunk/Boot Lid is pneumatically controlled and can have some or all of the following functions depending on the configuration codes as detailed on the Vehicle Data Card (List of Option Codes).
- Auto opening
- Auto or self closing
- Extension and retraction of Trunk/Boot Lid handle
- Pneumatically operated lock and unlock with mechanical (emergency key) overide
- Trunk/Boot Lid pull down function.
The positive and negative pressures required for the pneumatic control of the Trunk/Boot Lid functions are generated by the Pneumatic System Equipment (PSE) Pump.
Retractable Trunk Lid Grip (RTG) - Trunk/Boot Lid
Some M-B W220s have an extendable and retractable Trunk/Boot Lid handle called the Retractable Trunk Lid Grip (RTG) option. See also WIS 88.52 Retractable Trunk Lid Grip (RTG).
- Photo of a W220 2003 (Update) S500L with Retractable Trunk Lid Grip (RTG) in hidden or retracted position.
- Photo of a W220 2003 (Update) S500L with Retractable Trunk Lid Grip (RTG) in open or extracted position.
TBD (Will upload as soon as mine is working again!)
Remote Locking - Trunk/Boot Lid
Some M-B W220s have a self closing and remote locking Trunk/Boot Lid. What this means exactly is TBD.
Part Numbers - Trunk/Boot Lid
Locking Mechanism Actuator - Trunk/Boot Lid
- Locking Mechanism Actuator 220 750 0684
Issues - Trunk/Boot Lid
Common issues relating to the trunk/boot lid functions are;
- Hissing Sound on Trunk Closure
- Broken or Failed Pneumatic Actuators
- Cracked or broken pneumatic lines.
- Cannot remove the actuator rod to get the locking mechanism out of the trunk
- Open the Trunk/Boot when the Battery is Dead
How to Jump Start the Car and Open the Trunk/Boot when the Battery is Dead
Issue
A completely dead battery prevents the boot lid from being electrically opened. A jump start is not possible if you cannot access the battery as the W220 does not have accessible jump ports.
Solution
Extract the mechanical key from the Remote Key Fob and use it to open the Trunk. If that doesn't work you may have to charge the battery prior to jump starting the car.
- Pull the carpet back from the top under the front passenger side dash.
- Behind the Styrofoam insulation there is an aluminum plate.
- Unscrew the 3-4 bolts to get to the positive terminal.
- Hook up a charger and charge the battery as long as possible.
- After a while you should be able to start the car.
- If the trunk still will not open reset it by removing the 20A yellow fuse from under the rear right passenger seat fuse box.
- Leave it out for about 5 mins.
- Then put it back in and then try to open the Trunk.
- The Trunk should now open.
DIY - Removing Trunk Lid Lining
 |
 |
 |
 |
 |
 |
 |
 |
 |
DIY - Removing Trunk Lining
 |
 |
 |
 |
 |
 |
 |
 |
 |
Opening trunk without key
To open the trunk if for some reason it cannot be opened using smartkey or mechanical key, you can use this method which will cause only minor damage of lid covering.
- Detach the licence plate from the trunk lid covering.
- The covering (9) is a big plastic part mounted on the lid. Remove the covering:
- Pre-facelift:
- You will see two screws in the middle of covering (9). Remove them.
- You have to remove covering by force using plastic molding remover tool. Note, that there are 7 bolts (10) that are tightened from the inside to hold the covering (9) in place. You will damage plastic housing for these bolts in the covering. However, it is very common to see these housings already damaged. Furthermore, the covering holds to the lid just fine only using the two central screws.
- Facelift:
- You have to remove covering by force using plastic molding remover tool. Note, that there are 8 clips (10) and one screw in the center tightened from the inside that hold the covering (9) in place. You will damage the center nut of the covering. However, this damage is not critical since the covering holds to the lid just fine using only the clips.
- Pre-facelift:
- After covering is removed you will see three T30 torx bolts (12) holding the trunk lid handle. Unscrew them.
- Push the whole trunk lid handle inside through the hole while pushing the button.
- You hear that pop noise. Trunk lid is open.
- In case the release rod (14) that connects the trunk lid lock (1) to the trunk lid handle (13) is disconnected, you can use a needled nose pliers to release the rod and open the trunk.
 |
 |
 |
Welding trunk lid covering holes
Trunk lid has 7 (pre-facelift) or 8 (facelift) holes which are used to attach the trunk covering (9) to the trunk lid. It is common to see these holes being a source for moisture and rust inside the trunk lid. As an anti-rust measure these holes can be closed by welding. The trunk covering still remains attached to the trunk lid by two central screws (pre-facelift) or one central screw (facelift), although double sided type is recommended to prevent vibration of the covering.
 |
 |
DIY - Repair of Broken Pneumatic Actuator 01
With thanks to BenzWorld member 'subscriber' for posting an excellent description of his repair of a broken locking mechanism pneumatic actuator.
Note the broken plastic tabs on the perimeter of the actuator.
See http://www.benzworld.org/forums/w220-s-class/2532833-repair-part-220-750-0684-trunk.html
DIY - Repair of Broken Pneumatic Actuator 02
See WIS 88.52 Retractable Trunk Lid Grip (RTG) for a DIY repair of a broken actuator.
DIY - Repair of Pneumatic Actuator Pneumatic Solenoid Valves
Description - Pneumatic Actuator Pneumatic Solenoid Valves
In the Pneumatic Actuator there is a double solenoid valve which distributes the pneumatic pressure to the relevant actuator depending on the required result.
The exact description of which coil does what has yet to be determined and wasn't necessary for a thorough clean and bench test. It is something like the following: (Reference: HECK function on Pneumatic System Equipment (PSE) Pump.
- When the Boot/Trunk Lid is closed manually to the first position as identified by a loud click, the PSE HECK port provides +ve pressure (110KPa or 16psi) to the Boot/Trunk Lid Solenoid Valve Assembly and hence to the Large White Actuator which pulls the boot closed tightly, then the PSE HECK port changes to –ve pressure (19”Hg vacuum), which retracts the Handle (RTG), then returns the line to atmospheric pressure.
- When the Boot/Trunk Lid is commanded to open either by remote control on the key fob, by pressing the Boot/Trunk Lid button, or by pulling the internal Boot/Trunk Lid release button on the driver's door, the PSE HECK port provides +ve pressure (110KPa or 16psi) to the Boot/Trunk Lid Solenoid Valve Assembly and hence to the Small Black Actuator or "Hockey Puck" which opens the locking latch, thus releasing the lid which fully opens. +ve Pressure is also applied to the RTG Handle, which extends the Handle. After all this is finished the pneumatic line returns to atmospheric pressure.
DIY Clean and Regrease - Trunk Lid Actuator Pneumatic Solenoid Valves
Once the Boot/Trunk Lid Pneumatic Actuator is removed from the vehicle it can be dismantled on the work bench. See WIS 88.52 Retractable Trunk Lid Grip (RTG) for the removal method.
- Press in the two small plastic tabs and the Pneumatic Solenoid Valve Assembly can be with drawn.
- Remove the top front cover over the electrical connector.
- Then press in two small plastic tabs and remove the top rear cover.
Photo of disassembled Pneumatic Solenoid Valve Assembly
Closeup of coils and seals.
The electrical circuit diagram is very simple with the two coils just connected in parallel. A diode is also connected across the coils to reduce current surge when the coils are switched off. (Here is the theory: The magnetic energy stored in energised coils can generate a large spark across the operating switch when it is opened and consequently burn the electrical contacts in the switch. A diode provides a path for this excess energy to dissipate harmlessly.) The downside of having a diode in the circuit is that the electrical contacts are now polarised and correct polarity of any applied test voltage must be observed otherwise the diode will burn out. This just means that the '+' and '-' signs on the next diagram must be observed when applying a 12 Volt DC test voltage.
Circuit Diagram of Trunk Lid Actuator Pneumatic Solenoid Valves
- Reassemble in the reverse order but apply silicon dielectric or vacuum grease to the pneumatic seals before assembly.