Workspace

Cockpit

• (1) Combination switch
  • Turn signals
  • Windshield wipers
  • High beam
• (2) Cruise control lever
  • Cruise control
  • Distronic
• (3) Instrument cluster
• (4) Multifunction steering wheel
• (5) Gear range indicator, clock
• (6) Lever for voice control system
• (7) Front Parktronic warning indicator for right front area
• (8) Overhead control panel
• (9) Glove box lock
• (10) Glove box lid release
• (11) Glove box
• (12) Center console
• (13) Starter switch
• (14) Horn
• (15) Steering wheel adjustment stalk, Heated steering wheel
• (16) Parking brake pedal
• (17) Hood lock release
• (18) Parking brake release
• (19) Door control panel
• (20) Exterior lamp switch
• (21) Headlamp washer button
• (22) Front Parktronic warning indicator for left front area

Instrument cluster

• (1) Coolant temperature gauge
• (2) Fuel gauge with: Fuel reserve warning lamp
• (3) Left turn signal indicator lamp, Right turn signal indicator lamp
• (4) Speedometer with: ESP warning lamp, Distance warning lamp (Vehicles without Distronic: Warning lamp without function. It illuminates when the ignition is on. It should go out when the engine is running.)
• (5) Tachometer
• (6) Right display with: Seat belt telltale, High beam headlamp indicator, Antilock Brake System (ABS) warning lamp
• (7) Reset button
• (8) Display with:
  • Program mode
  • Gear range indicator
  • Digital clock (see COMAND operating in structions)
• (9) Multifunction display with:
  • Trip odometer
  • Main odometer
  • Stored speed for: Cruise control, Distronic
• (10) Outside temperature indicator
• (11) Left display with:
  • Supplemental restraint system indicator lamp
  • Brake warning lamp
  • Engine malfunction indicator lamp
  • Tire pressure warning lamp
• (12) Knob for instrument cluster illumination

Multifunction steering wheel

• (1) Multifunction display, Operating control system
• (2) Selecting the submenu or setting the volume
• (3) Telephone: Press button
  • to take a call, to dial a call
  • to end a call, to reject an incoming call
• (4) Menu systems: Press button
  • for next system
  • for previous system
• (5) Moving within a menu: Press button
  • for next display
  • for previous display

Center console

Upper part

• (1) Switch for rear window sunshade
• (2) Parktronic system deactivation switch
• (3) Airmatic or ABC switch
• (4) Level control switch
• (5) Central locking switch, Anti-theft alarm system indicator lamp
• (6) Hazard warning flasher on/off switch
• (7) Central unlocking switch
• (8) ESP control switch
• (9) Rear seat head restraints, switch for folding down
• (10) Tow-away alarm switch
• (11) COMAND system
• (12) Automatic climate control
• (13) Ashtray, Lighter

Lower part

• (1) KEYLESS-GO start/stop button
• (2) Gear selector lever for automatic transmission
• (3) PASSENGER AIRBAG OFF indicator lamp
• (4) Thumbwheel for setting distance in Distronic
• (5) Distronic distance warning function on/off switch
• (6) Lower storage compartments
• (7) Program mode selector for automatic transmission

Overhead control panel

• (1) Left reading lamp on/off
• (2) Rear interior lighting on/off
• (3) Right reading lamp on/off
• (4) Interior lighting control
• (5) Sliding/pop-up roof
• (6) Hands-free microphone for Tele Aid (emergency call system), telephone, and voice control system
• (7) Rear view mirror
• (8) Garage door opener
• (9) Tele Aid (emergency call system) button

Door control panel

• (1) Door handle
• (2) Memory function (for storing seat, exterior mirror, and steering wheel settings)
• (3) Seat heating, Seat ventilation
• (4) Seat adjustment
• (5) Exterior mirror adjustment
• (6) Switches for opening/closing front door windows
• (7) Rear passenger compartment override switch
• (8) Switches for opening/closing rear windows
• (9) Remote trunk lid release switch, Trunk lid opening/closing system switch

Unlocking with the SmartKey

• (1) Lock button
• (2) Unlock button for trunk lid
• (3) Unlock button
• (4) Panic button

• Press unlock button on the SmartKey. All turn signal lamps flash once. The locking knobs in the doors move up.
• Get in the vehicle and insert the SmartKey in the starter switch.

Starter switch positions

• 0 For removing SmartKey
• 1 Power supply to some electrical consumers, such as seat adjustment
• 2 Ignition (power supply for all electrical consumers) and driving position
• 3 Starting position

• The SmartKey can only be removed from the starter switch with the gear selector lever in position P.
• If the SmartKey cannot be turned in the starter switch, the battery may not be sufficiently charged.
  • Check the battery and charge it if necessary.
  • Get a jump start.
• To prevent accelerated battery discharge or a completely discharged battery, always remove the SmartKey from the starter switch when the engine is not in operation.

Unlocking with KEYLESS-GO

If your vehicle is equipped with the KEYLESS-GO function, your vehicle checks whether the SmartKey with KEYLESS-GO is valid when you grasp the door handle. If your SmartKey with KEYLESS-GO is valid, the doors will unlock, and you can open them. The function of the SmartKey overrules the KEYLESS-GO function.

To unlock the vehicle, the SmartKey with KEYLESS-GO must be outside the vehicle, no further than approximately 3 feet (1 meter) away from the door. Grasp the outside door handle. All turn signal lamps flash once. The locking knobs in the doors move up.

If the SmartKey is inside the vehicle, pressing the KEYLESS-GO start/stop button on the gear selector lever corresponds to turning the SmartKey to the various starter switch positions.

Before you press the KEYLESS-GO start/stop button (1), the vehicle's on-board electronics have status 0 (as with SmartKey removed). The SmartKey with KEYLESS-GO must be located in the vehicle.

• Make sure the gear selector lever is set to P.
• Do not depress the brake pedal.

Position 1 Press the KEYLESS-GO start/stop button (1) once. This supplies power to some electrical consumers, such as seat adjustment. If you now press the KEYLESS-GO start/stop button once again, the ignition (position 2) is switched on. Twice, the power supply is again switched off.

Ignition (or position 2) Press the KEYLESS-GO start/stop button (1) twice. This supplies power to all electrical consumers. All the lamps in the instrument cluster come on. If you now press the KEYLESS-GO start/stop button once, the power supply is again switched off.

Seat adjustment

The seat adjustment switches are located on the front doors.

• (1) Head restraint height
• (2) Seat height
• (3) Seat cushion tilt
• (4) Seat cushion depth
• (5) Seat fore and aft adjustment
• (6) Seat backrest tilt

To adjust the seat switch on ignition or open the respective door.

Seat fore and aft adjustment Press the switch forward or backward in the direction of arrow (5). Adjust seat to a comfortable seating position that still allows you to reach the accelerator/brake pedal safely. The position should be as far to the rear as possible, consistent with ability to properly operate controls.

Seat cushion tilt Press the switch up or down in the direction of arrow (3) until your upper legs are lightly supported.

Seat cushion depth Press the switch forward or backward in the direction of arrow (4) until your legs are supported comfortably.

Seat backrest tilt Press the switch forward or backward in the direction of arrow (6) until your arms are slightly angled when holding the steering wheel.

Seat height Press the switch up or down in the direction of arrow (2).

Head restraint height Press the switch up or down in the direction of arrow (1).

Head restraint tilt Manually adjust the angle of the head restraint. Push or pull on the lower edge of the head restraint cushion.

Unoccupied front passenger seat automatic adjusting The feature below is deactivated at the factory. If you wish to have it activated, contact an authorized Mercedes-Benz Center. The front passenger seat head restraint automatically lowers after a few seconds when the front passenger seat is not occupied. This improves the driver's outward view as well as the forward view from the rear passenger compartment. When the front passenger seat is occupied again, the front passenger seat head restraint returns to the last set position within a few seconds. If the front passenger seat was moved fore or aft while not being occupied, the front passenger seat head restraint returns to a position that corresponds best with the seat’s axial position when the seat is occupied again.

Steering wheel adjustment

The stalk for steering wheel adjustment is located on the steering column (lower left). To adjust the steering column switch on ignition or open the driver's door.

• (1) Adjusting steering column, in or out. Move stalk forward or back in the direction of arrow (1) until a comfortable steering wheel position is reached with your arms slightly bent at the elbow.
• (2) Adjusting steering column, up or down. Move the stalk up or down in the direction of arrow (2). Make sure your legs can move freely and all the displays (incl. malfunction and indicator lamps) on the instrument cluster are clearly visible.

Memory ...

The memory function lets you store settings for the steering wheel together with the settings for the exterior rear view mirrors and the seat position.

Adjusting mirrors

Adjust the interior and exterior rear view mirrors before driving so that you have a good view of the road and traffic conditions.

Interior rear view mirror Manually adjust the interior rear view mirror.

Exterior rear view mirror The buttons are located on the driver’s door.

• (1) Driver’s side exterior rear view mirror button
• (2) Passenger-side exterior rear view mirror button
• (3) Adjustment button

• Switch on ignition.
• Press button (1) for the left mirror or button (2) for the right mirror.
• Push adjustment button (3) up, down, left, or right according to the desired setting.

Heating At low ambient temperatures, the mirrors will be heated automatically.

Fastening the seat belts

• (1) Release button
• (2) Buckle
• (3) Latch plate

• Pull the seat belt smoothly from the seat belt outlet.
• Place the shoulder portion of the belt across the top of your shoulder and the lap portion across your hips.
• Push latch plate (3) into buckle (2) until it clicks.
• If necessary, tighten the lap portion to a snug fit by pulling shoulder portion up.

Proper use of seat belts

• Do not twist the belt when fastening.
• Adjust seat belt so that the shoulder portion is located as close as possible to the middle of the shoulder (it should not touch the neck). Never pass the shoulder portion of the belt under your arm.
• Position the lap belt as low as possible on your hips (over hip joint) and not across the abdomen.
• Place the seat backrest in a nearly upright position. Never use a seat belt for more than one person at a time.
• Do not fasten a seat belt around a person and another object at the same time.
• Check your seat belt during travel to make sure that it is properly positioned.
• Make sure that the seat belt is always fitted snugly. Take special care of this when wearing loose clothing.

Press the seat belt release button. Allow the retractor to completely rewind the seat belt by guiding the latch plate.

Automatic transmission

Gearshift pattern for automatic transmission:

• P Park position with gear selector lever lock
• R Reverse gear
• N Neutral
• D Drive position

Driving

• Depress the brake pedal.
• Move gear selector lever to position D or R.
• Release the brake pedal.
• Carefully depress the accelerator pedal.

Once the vehicle is in motion, the automatic central locking system engages and the locking knobs drop down. You can open a locked door from the inside. Open doors only when conditions are safe to do so. You can deactivate the automatic locking using the control system.

Turning off the engine

• Place the gear selector lever in position P.

Always set the parking brake in addition to shifting to position P. On steep slopes, turn the front wheels towards the curb.

Turning off with the SmartKey

• Turn the SmartKey in the starter switch to position 0 and remove it. The immobilizer is activated.

The SmartKey can only be removed from the starter switch with the gear selector lever in position P.

Turning off the engine with KEYLESS-GO

• Place the gear selector lever in position P.
• Press the KEYLESS-GO start/stop button to shut off the engine.

With the driver's door closed, the starter switch is now in position 1. With the driver’s door opened, the starter switch is set to position 0, same as SmartKey removed from starter switch.

In order to avoid damaging the transmission,

• wait for the gear selection process to complete before setting the vehicle in motion.
• place the gear selector lever in position R only when the vehicle is stopped.

After a cold start, the automatic transmission shifts at a higher engine revolution. This allows the catalytic converter to reach its operating temperature earlier.

Do not run cold engine at high engine speeds. Running a cold engine at high engine speeds may shorten the service life of the engine.

If you hear a warning signal, you have tried to turn off the engine while the gear selector lever is not in P.

Starting with the SmartKey

• Make sure the gear selector lever is set to P.
• Do not depress accelerator.
• Turn the SmartKey in the starter switch to position 3 and hold until the engine starts. You can also use the "touch-start" function. Turn the SmartKey to position 3 and release it again immediately. The engine then starts automatically.
• Depress the brake pedal. The gear selector lever lock is released.

Starting with KEYLESS-GO

You can start your vehicle without the SmartKey in the starter switch using the KEYLESS-GO start/stop button on the gear selector lever. The SmartKey with KEYLESS-GO must be located in the vehicle.

• Make sure the gear selector lever is set to P.
• Depress the brake pedal during the starting procedure. Do not depress accelerator.
• Press KEYLESS-GO start/stop button (1) once. The engine starts automatically if the SmartKey with KEYLESS-GO is in the vehicle.

Starting difficulties If the engine does not start as described, carry out the following steps:

• If you are starting the engine with the SmartKey, turn SmartKey in starter switch to position 0 and repeat starting procedure.
• If you are starting the engine with KEYLESS-GO: Close any doors that may be open to allow for better detection of the SmartKey with KEYLESS-GO or start the engine with the SmartKey as radio signals from another source may be interfering with the SmartKey with KEYLESS-GO.

Parking brake

• (1) Parking brake pedal
• (2) Parking brake release handle

Release the parking brake by pulling handle (2). The indicator lamp in the instrument cluster goes out.

Step firmly on parking brake (1). When the engine is running, the indicator lamp in the instrument cluster illuminates.

If you hear a warning signal and a message appears in the multifunction display when driving off, you have forgotten to release the parking brake. Release the parking brake.

Switching on headlamps

Exterior lamp switch

• (1) Off
• (2) Low beam headlamps on

With the SmartKey removed and the driver’s door open, a warning sounds if the vehicle’s exterior lamps are not switched off.

=Turn signals and high beam

Combination switch The combination switch is located on the left of the steering column.

• (1) Turn signals, right
• (2) Turn signals, left

To signal minor directional changes, move combination switch to point of resistance only and release. The turn signal flashes three times.

High beam Push the combination switch forward. The high beam headlamps are switched on. The high beam headlamp indicator in the tachometer comes on.

Windshield wipers

The combination switch is located on the left of the steering column. Combination switch

• (1) Single wipe
• (2) Switching on windshield wipers

Switching on windshield wipers

• Make sure the ignition is switched on. All the lamps in the instrument cluster come on.
• Turn the combination switch to the desired position depending on the intensity of the rain.
• 0 Windshield wipers off
• I Intermittent wiping (interval dependent on wetness of windshield)
• II Normal wiper speed
• III Fast wiper speed

Wiping will not occur with a door open.

Single wipe Press switch briefly in the direction of arrow (1). The windshield wipers wipe one time without washer fluid.

Wiping with windshield washer fluid Press switch in the direction of arrow (1) past the resistance point. The windshield wiper operates with washer fluid.

Coolant

The coolant temperature is above 248°F (120°C) The coolant is too hot and is no longer cooling the engine.

• Stop the vehicle as soon as possible and turn off the engine. Allow engine and coolant to cool.
• Check the coolant level and add coolant if necessary.

Excessive coolant temperatures trigger a warning message in the multifunction display.

Locking

After exiting the vehicle press the lock button on the SmartKey. All turn signal lamps flash three times. The locking knobs on the doors move down.

• (1) Lock button on the door handle.

After exiting the vehicle, press lock button 1 on the door handle or on the trunk lid. All turn signal lamps flash three times. The locking knobs on the doors move down.

Occupant safety

In this section you will learn the most important facts about the restraint systems of the vehicle. The restraint systems are:

• Seat belts
• Emergency tensioning device
• Airbags
• Child seats
• Child seat recognition
• Lower anchors and tethers for children (LATCH)

As independent systems, their protective effects work in conjunction with each other.

The SRS indicator lamp in the instrument cluster comes on

• for about four seconds when you turn the SmartKey in the starter switch to position 1 or press the KEYLESS-GO start/stop button once. It then goes out briefly, comes on again and remains lit until you start the engine.
• for about four seconds when you start the engine by turning the SmartKey or pressing the KEYLESS-GO start/stop button.
• The SRS indicator lamp remains lit if the SmartKey is turned to position 2 and left there or the KEYLESS-GO start/stop button is pressed twice. The

indicator lamp will go out when you start the engine.

The restraint systems are fully operational if the SRS indicator lamp is not lit when the engine is running. A malfunction in the system has been detected if the SRS indicator lamp:

• fails to extinguish after approximately four seconds.
• does not come on at all.
• comes on after the engine was started or while driving.

In the event that the SRS indicator lamp comes on during driving or does not come on at all, the SRS self-check has detected a malfunction. For your safety, we strongly recommend that you visit an authorized Mercedes-Benz Center immediately to have the system checked; otherwise the SRS may not be activated when needed in an accident, which could result in serious or fatal injury, or it might deploy unexpectedly and unnecessarily which could also result in injury.

Airbags are designed to reduce the potential of injury and fatality in certain frontal impacts (front airbags), side impacts (side impact airbags and head protection window curtain airbags) or rollovers (head protection window curtain airbags). However, no system available today can totally eliminate injuries and fatalities. The activation of the airbags temporarily releases a small amount of dust from the airbags. This dust, however, is neither injurious to your health, nor does it indicate a fire in the vehicle. The dust might cause some temporary breathing difficulty for people with asthma or other breathing trouble. To avoid this, you may wish to get out of the vehicle as soon as it is safe to do so. If you have any breathing difficulty but cannot get out of the vehicle after the airbag inflates, then get fresh air by opening a window or door.

For maximum protection in the event of a collision always be in normal seated position with your back against the seat backrest. Fasten your seat belt and ensure that it is properly positioned on your body. Since the airbag inflates with considerable speed and force, a proper seating and hands on steering wheel position will help to keep you at a safe distance from the airbag. Occupants who are unbelted, out of position or too close to the airbag can be seriously injured by an airbag as it inflates with great force in the blink of an eye:

• Sit properly belted in a nearly upright position with your back against the seat backrest.
• Adjust the driver seat as far as possible

rearward, still permitting proper operation of vehicle controls. The distance from the center of the driver’s breastbone to the center of the airbag cover on the steering wheel must be at least 10 in (25 cm) or more. You should be able to accomplish this by a combination of adjustments to the seat and steering wheel.

• Do not lean with your head or chest close to the steering wheel or dashboard.
• Keep hands on the outside of steering wheel rim. Placing hands and arms inside the rim can increase the risk and potential severity of hand/arm injury when driver front airbag inflates.
• Adjust the front passenger seat as far as possible rearward from the dashboard when the seat is occupied.
• Occupants, especially children, should never lean their heads in the area of the door where the side airbag inflates.

This could result in serious injuries or death should the airbag be triggered. Always sit nearly upright, properly use the seat belts and appropriate size infant or child restraint system.

• Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz authorized BabySmart TM compatible child seat, which operates with the BabySmart TM system installed in the vehicle to deactivate the passenger front airbag when it is properly installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this happens, serious or fatal injury will result.

Accident research shows that the safest place for children in an automobile is in the rear seat. Should you choose to place a child 12 years old or under in the front passenger seat of your vehicle, you must properly use a BabySmart TM child restraint which will turn off the passenger front airbag. BabySmart TM will not, however, turn off any side impact airbag.

Airbags are designed to activate only in certain frontal (front airbags) impacts, side impacts (side impact and head protection window curtain airbags) which exceed preset thresholds, and in certain rollovers (head protection window curtain airbags). Only during these events will they provide their supple- mental protection. The driver and passengers should always wear their seat belts. Otherwise it is not possible for airbags to provide their supplemental protection.

In case of other types of impacts and impacts below airbag deployment thresholds, airbags will not be activated. The driver and passengers will then be protected to the extent possible by a properly fastened seat belt. A properly fastened seat belt is also needed to provide the best possible protection in a rollover.

• Airbags and pyrotechnic emergency tensioning devices (ETDs) are designed to function on a one-time only basis. An airbag or ETD that was activated must be replaced. PRE-SAFE has electrically operated reversible pre-tensioners in addition to the pyrotechnic ETDs.
• An airbag system component within the steering wheel gets hot after the airbag has inflated. Do not touch.

Front airbags

• (1) Driver airbag
• (2) Passenger front airbag

Driver and passenger front airbags are deployed:

• in the event of a frontal impact
• if impact exceeds a preset deployment threshold
• independently of the side impact airbags

The airbags will not deploy in impacts which do not exceed the system’s deployment thresholds. You will then be protected by the fastened seat belts.

The passenger front airbag will only be deployed if:

• the front passenger seat is occupied
• the PASSENGER AIRBAG OFF indicator lamp in the center console is not lit
• the impact exceeds a preset deployment threshold

Do not place objects heavier than 20 lbs (9 kg) on the front passenger seat. This could cause the front or side impact airbag on the front passenger side to deploy in a crash which exceeds the system's deployment threshold.

Side impact airbags, window curtain airbags

• (1) Window curtain airbag
• (2) Side impact airbags

The side impact airbags and window curtain airbags are deployed:

• on the impacted side of the vehicle
• in impacts exceeding a preset deployment threshold
• independently of the front airbags

In addition, the window curtain airbags are deployed:

• in certain vehicle rollovers

The side impact airbags and window curtain airbags are not deployed in impacts which do not exceed the system’s deployment threshold. The front passenger side impact airbag will only deploy if the system senses that the front passenger seat is occupied.

Emergency tensioning device (ETD), seat belt force limiter The seat belts for the front and rear outer seats are equipped with emergency tensioning devices and belt force limiters.

The ETD is designed to activate in the following cases:

• in frontal or rear-end impact exceeding a preset severity level
• in certain vehicle rollovers
• if the restraint systems are operational and functioning correctly (see SRS indicator lamp)

The ETDs for the front seats will only activate if the respective front seat belt is fastened (latch plate properly inserted into buckle). The ETDs for the rear outer seats will activate with or without the respective seat belt fastened.

In an impact, emergency tensioning devices remove slack from the belts in such a way that the seat belts fit more snugly against the body. Belt force limiters reduce the force exerted by the seat belts on occupants during a crash.

A pyrotechnic emergency tensioning device (ETD) that was activated must be replaced.

PRE-SAFE has electrically operated reversible pre-tensioners that do not require replacement after activation.

Automatic comfort-fit feature seat belt An automatic comfort-fit feature for front seats and for the rear outer seats (only for vehicles with electrically adjustable rear bench seat or with individual seats in the rear) reduces the retracting force of the seat belts when they are in normal use.

Preventive occupant safety (PRE-SAFE) The PRE-SAFE system is intended to reduce the effects of an accident on properly seat belted vehicle occupants.

Your vehicle automatically takes preventive measures to better protect the occupants in the following hazardous situations:

• You execute an emergency braking maneuver and the Brake Assist System is activated.
• The PRE-SAFE system detects a critical driving dynamics situation.

The PRE-SAFE systems are activated in the previously described circumstances only at speeds exceeding 22 mph (35 km/h).

In such cases, the following systems are automatically activated:

• A front seat belt with the seat belt buckled is pre-tensioned electrically.
• If the occupied front passenger seat or rear seats are in an unfavorable position,

they are adjusted to a better position. Rear seat adjustment occurs only in vehicles with individual seats in the rear.

• The sliding/pop-up roof closes if the vehicle is in a severe skid or is spinning.

When the driving dynamic situation has passed without an accident occurring, the pre-tensioning on the seat belts is deactivated. You can then adjust the seats and the sliding sunroof to their previous position.

If the seat belts do not release: Adjust the backrest or seat slightly to the rear until the seat belt tension is diminished. The locking mechanism releases.

Seat belts When the engine is started, the seat belt telltale illuminates to remind you and your passengers to fasten your seat belts. If the driver’s seat belt is not fastened before the engine is started, the seat belt telltale illuminates and a warning chime sounds for approximately six seconds when the engine is started.

Never ride in a moving vehicle with the seat backrest in an excessively reclined position as this can be dangerous. You could slide under the seat belt in a collision. If you slide under it, the belt would apply force at the abdomen or neck. That could cause serious or even fatal injuries. The seat backrest and seat belt provide the best restraint when the wearer is in a nearly upright position and the belt is properly positioned on the body.