Glove compartment: Difference between revisions
Jump to navigation
Jump to search
(→Parts: added) |
|||
| Line 42: | Line 42: | ||
* 2 - Glove compartment | * 2 - Glove compartment | ||
|} | |} | ||
[[File:W220_glove_box_cable_disconnected.jpg|thumb|none|Control cable disconnected.]] | |||
# Remove glove compartment | # Remove glove compartment | ||
Revision as of 19:18, 17 April 2017
Removing and installing glove compartment
|
|
|
|
- Open glove compartment lid (6)
- Unclip glove compartment lamp (1) and disconnect connector
- Remove plugs (2)
- Unscrew screws (3)
- Unscrew screws (4)
- Pull glove compartment (5) completely out of instrument panel
- Unhook control cable (7) on lock (8) on glove compartment (5). When unhooking the control cable (7) ensure that the slider (arrow) is not pulled out of the lock (8).
- Install in opposite order
Removing and installing key block on glove compartment lid
|
|
- Remove glove compartment
- Unscrew mounting screws for key block (1). Key block (1) is screwed onto instrument panel (2) from rear (two Torx 20 screws).
- Remove key block (1) to side
- Unhook control cable from eye (arrow) on key block (1). Installation: Check function of control cable, adjust with knurled nut if necessary.
- Install in opposite order
Removing and installing glove compartment lid
|
|
|
|
- Remove glove compartment (2)
- Unclip damping strip (8) on right from strap (5), (arrow) on glove compartment lid (1)
- Remove rubber stops (3) from strap (5)
- Pull expanding anchor (4) out of glove compartment (2). Pull expanding anchor out of glove compartment from inside.
- Remove glove compartment lid (1) together with hinges (6) uniformly downward
- Install in opposite order
- Adjust glove compartment lid
Disassembling and reassembling glove compartment lid
|
|
Adjusting glove compartment lid
|
|
|
During entire operation pay attention to uniform transition and gap all the way around (arrows) on the glove compartment lid (1) in relation to the instrument panel (2).
- Pull out both expanding anchors (3) from glove compartment lid (4) with small screwdriver
- Close glove compartment lid (1), adjust horizontal gap and transitions (arrows). Glove compartment lid (1) can be adjusted increment for increment on the hinge.
- Carefully open glove compartment lid (1) and press in expanding anchors (3)
- Check gap width at side, adjust.
- Differences in the gap width can be corrected slightly by loosening the mounting screws (4 each) for the glove compartment (4) and then moving.
- Check transition from glove compartment lid (1) to instrument panel (2), adjust. Adjustment is possible by screwing the two stop screws (5) in or out.
- Check for easy motion and proper function
 |
 |
 |
 |
Parts
Key block
| Part No. | Notes |
|---|---|
| A2206800284 (left hand drive vehicles) | Replaced by: A2206800784 |
| A2206800784 (left hand drive vehicles) | |
| A2206800384 (right hand drive vehicles) | Replaced by: A2206800884 |
| A2206800884 (right hand drive vehicles) |
Lock cylinder
| Part No. | Notes |
|---|---|
| A2206890001 | State lock number when ordering; Theft relevant part; Replaced by: A2206890101 |
| A2206890101 | State lock number when ordering; Theft relevant part |
Cap
| Part No. | Notes |
|---|---|
| A2206890030 (left hand drive vehicles) | To Date: 01/09/2002 |
| A2206890330 (left hand drive vehicles) | From Date: 30/09/2002 |
| A2206890130 (right hand drive vehicles) | To Date: 01/09/2002 |
| A2206890430 (right hand drive vehicles) | From Date: 30/09/2002 |
Cable
Part No. A0009964672.
Worn glove box release button
Very popular issue is worn glove box release button. The color layer after years peals off leaving the plastic cap visible.
 |
  |
Worn cap on the key block can be replaced by ordering the cap (part number A2206890330 + color code) for around EUR 6.
To replace worn release button cap the whole lock cylinder has to be replaced (part number A2206800784 + color code) for around EUR 100. The lock mechanism must be removed and transferred to the new part.
 |
 |