EVAP system

The Evaporative Emission Control System (EVAP) is used to prevent gasoline vapors from escaping into the atmosphere from the fuel tank and fuel system at all times.

A typical system consists of the fuel tank, an EVAP vapor storage canister full of charcoal, valves, hoses and a sealed fuel tank gas cap. The EVAP system is designed to stop fuel system fumes from leaking directly into the atmosphere. Vent lines from the fuel tank pass vapors to the vapor canister, where they are trapped and stored until the engine is started. When the engine is warm and the vehicle is going down the road, the PCM then opens a purge valve allowing the vapors to be drawn from the storage canister into the intake manifold. The fuel vapors are then burned in the engine along with the air/fuel mixture.

Fuel evaporation control system function

Shown on engine 119 75 - Fuel tank 77 - Activated charcoal canister N3/10 - ME control unit Y58/1 - Purge control valve a - Pressurization line

Shown on ENGINE 120 75 - Fuel tank 77 - Activated charcoal canister 93 - Expansion reservoir (only with optional ski bag) M16/3 - Right EA/CC/ISC actuator Position on left of engine M16/4 - Left EA/CC/ISC actuator Position on right of engine N3/11 - Left ME-SFI [ME] control unit N3/12 - Right ME-SFI [ME] control unit Y58/2 - Switchover valve Left regeneration Y58/3 - Switchover valve Right regeneration a - Pressurization line

The fuel evaporation control system prevents fuel vapors escaping to atmosphere. This is done by storing the fuel vapors temporarily in the activated charcoal canister.

When the engine is running, the fuel vapors stored in the activated charcoal canister are drawn off through the purge control valve and combusted in the engine. The activated charcoal canister is purged (re-generated) at:

• Coolant temperature > 70 °C
• Blocking time after engine start elapsed, approx. 2 minutes
• Engine not in deceleration mode

The purge quantity is controlled by the ME-SFI control unit operating the purge control valve. The purge quantity is determined by constantly opening and closing the purge control valve for on and off periods of various lengths.

The idle speed control prevents changes in engine speed resulting from purging. A richer or leaner fuel-air mixture is produced in line with the charge of the activated charcoal canister with fuel vapors.

Air admission to fuel tank. Air is admitted through the activated charcoal canister. This is done through the activated charcoal canister, whereby air is drawn out of the vent/breather line or fuel vapors are drawn from the activated charcoal canister into the fuel tank.

Air release from fuel tank. The fuel tank is vented through the activated charcoal canister. The fuel vapors flow to the activated charcoal canister, where they are stored or drawn into the intake manifold in case of simultaneous regeneration.

Vent valve. On vehicles fitted with a vent valve the fuel tank is vented from a pressure of 30 to 50 mbar, and air admitted at a vacuum of 1 to 16 mbar. In addition, this prevents overfilling the fuel tank.

USA as of MY 98. During refueling the fuel vapors are collected at the filler neck and passed to the activated charcoal filter (ORVR = Onboard Refueling Vapor Recovery). Large activated charcoal canister.

Engines with charging (compressor or turbocharger). A check valve in the purge line prevents the boost pressure building up toward the activated charcoal canister.

Model 215 from chassis no. A046659 (approx. 23.3.05), without USA and model 220 from chassis no. 469233 (ca. 23.3.05), without USA with ski bag (Code 282) or cooling compartment in rear backrest (Code 308) or with retrofitted additional vent valve (76/1):

75 - Fuel tank 76 - Vent valve (standard) 76/1 - Vent valve (additional from series production breakpoint or retrofitted) 77 - Activated charcoal canister N3/10 - ME-SFI [ME] control unit Y58/1 - Purge control valve A - to intake manifold B - Air admission C - Line to fuel tank D - Line to purge control valve

The additional vent valve (76/1) prevents the vacuum from the intake manifold passing over the activated charcoal canister through to the fuel tank for enabled purging. For this purpose, the valve closes as soon as a membrane is pressurized with vacuum pressure from the activated charcoal canister. If excess pressure or vacuum pressure affects the other valve connection, it opens immediately. This means aeration/venting of the fuel tank is then possible in an unlimited fashion via the standard vent valve (76).

Pay attention to the installation position of the vent valve (76/1). Check aeration at the activated charcoal canister for contamination (e.g. dust, spider's webs).

Parts

EVAP system related parts in EPC

Connection diagram for evaporative emission control system (M113)

Shown on engine 113 from 09/97 in model 210 17 - Fuel distributor 19 - Intake manifold 75 - Fuel tank 77 - Activated charcoal canister A - Activated charcoal canister line to purge control valve B - Purge control valve line for to intake manifold C - Vent line from activated charcoal canister to fuel tank D - Line for activated charcoal canister vent valve to fuel tank M3 - Fuel pump M16/1 - EA/CC/ISC [EFP/TPM/LLR] actuator (only models 129, 210) Y58/1 - Purge control valve Y62 - Fuel injection valves

Connection diagram for evaporative emission control system (M112)

Shown on engine 112 from 09/97 in model 210 17 - Fuel distributor 19 - Intake manifold 45 - Filler neck (with connection for on-board refueling vapor recovery ORVR) 55/1 - Fuel filter 75 - Fuel tank 77 - Activated charcoal canister M3 - Fuel pump M16/1 - EA/CC/ISC [EFP/TPM/LLR] actuator (only models 129, 210) Y58/1 - Purge control valve Y62 - Fuel injection valves A - Activated charcoal canister line to purge control valve B - Purge control valve line for to intake manifold C - Activated charcoal canister line to fuel tank D - Fuel tank line to activated charcoal canister E - Fuel filter degassing line to fuel tank F - Fuel filter fuel tank fuel return line to fuel tank

Remove/install activated charcoal canister

Shown on MODEL 220 77 - Activated charcoal canister A - Activated charcoal canister purge control valve line D - Vent valve line from activated charcoal canister to fuel tank

1. Raise vehicle.
2. Remove rear left wheelhousing liner
3. Detach activated charcoal canister - purge control valve line (A) and vent valve line - activated charcoal canister to fuel tank (D) at activated charcoal canister (77)
4. Remove activated charcoal canister (77). Lift up and out.
5. Install in the reverse order