WIS 07.61 Gasoline Engine and Injection System ME
Heated Oxygen Sensors (HO2S) or Lambda Sensors
- G3/3 Left and G3/4 Right are the Heated Oxygen Sensors before or upstream of the TWC (KAT).
- G3/5 Left and G3/6 Right are the Heated Oxygen Sensors after or downstream of the TWC (KAT).
Heated Oxygen Sensor How It Works
The Heated Oxygen Sensor (HO2S) or Lambda Sensor produces a voltage from approximately 1.0 V during rich operating conditions to 0.01 V (10 mV) during lean operating conditions. The HO2S is like an open circuit and produces no voltage when it is below 360C (600F).
The powertrain control module (PCM) supplies a bias voltage of about 450 mV between the heated oxygen sensor (HO2S) high signal and low signal circuits. The HO2S varies the voltage within a range of about 1,000 mV when the exhaust is rich, down through about 10 mV when exhaust is lean. The PCM constantly monitors the HO2S signal during Closed Loop operation and compensates for a rich or lean condition by decreasing or increasing the fuel injector pulse width as necessary. If the HO2S voltage remains at or near the 450 mV bias for an extended period of time, P0154 diagnostic trouble code (DTC) will be set.
Heated Oxygen Sensor Resistance of Heater
- Measured as 9.2 Ohms, specified value TBD.
Heated Oxygen Sensor Cable Lengths
Note two different lengths.
- G3/3 Left and G3/4 Right Front or Upstream HO2S (Long Cable). Wire length: 440mm (17.3 inches) sensor washer to end of connector. Total length: 460mm.
- G3/5 Left and G3/6 Right Rear or Downstream HO2S (Short Cable). Wire length: 322mm (12.7 inches) sensor washer to end of connector. Total length: 340mm.
Heated Oxygen Sensor Connector Pin Diagram
HO2S Wire Colours
- Pin 1 White Heater
- Pin 2 White Heater
- Pin 3 Grey O2 Sensor Low
- Pin 4 Black O2 Sensor High
HO2S Connector to Power Control Module (N3/10) Cable Wire Colours
- Pin 1 Red or Red/Green Heater Ground
- Pin 2 Brown or Brown/Black Heater +12V
- Pin 3 Green O2 Sensor Low
- Pin 4 Black O2 Sensor High
Electrical Wiring Diagram HO2S Upstream of TWC [KAT]
Heated Oxygen Sensor Fault Codes
- P20BF-004 G3/3 Left HO2S before TWC (KAT) open circuit in sensor heater line (P0156)
- P2082-004 G3/3 Left HO2S before TWC (KAT) open circuit (P0154)
Contamination Note
Contamination of the oxygen sensor can result from the use of an inappropriate RTV sealant (not oxygen sensor safe) or excessive engine coolant or oil consumption. Remove the HO2S and visually inspect the portion of the sensor exposed to the exhaust stream in order to check for contamination. If contaminated, the portion of the sensor exposed to the exhaust stream will have a white powdery coating. Silicon contamination causes a high but false HO2S signal voltage (rich exhaust indication). The control module will then reduce the amount of fuel delivered to the engine, causing a severe driveability problem. Eliminate the source of contamination before replacing the oxygen sensor.
Heated Oxygen Sensors DIY Articles
http://www.benzworld.org/forums/w203-c-class/1474361-p0154-code-wont-go-away.html
http://www.benzworld.org/forums/w203-c-class/1474361-p0154-code-wont-go-away-2.html
http://www.hotrodlane.cc/New%20LS%20Links%20Page/LS%20trouble%20codes/DTC%20P0154.htm