Ignition system: Difference between revisions

From W220 S-Class Encyclopedia
Jump to navigation Jump to search
No edit summary
(significant rewrite and update)
Line 1: Line 1:
Back to '''[[Index]]'''
==Ignition System==
==Ignition System==
[[File:W220_EPC_ignition_system.png|thumb|none|Parts in [[EPC]] related to ignition system.]]
[[File:W220_EPC_ignition_system.png|thumb|none|Parts in [[EPC]] related to ignition system.]]


The W220 S Class series uses a twin-spark ignition coil with kV pickup (a test connector on each coil pack) and dual spark plugs per cylinder.
This page covers W220 petrol engines M112 (V6 engine used in [[S350]]) and M113 (V8 engine used in [[S430]] and [[S500]]).
 
'''Warning:''' No tests such as holding an ignition HT Wire at a distance from ground and observing a spark must be performed.
 
'''Warning:''' Do not operate the ignition system at starting speed unless all of the HT Wires are connected.
 
'''Warning:''' Before working at cranking speed eg to check compression pressure, switch off ignition and disconnect Ignition Control Unit from 12V.
 
==Spark Plugs==
 
===Parts===
Make sure that the spark plugs are for the correct engine.
The plugs listed above are for facelift S350 and S500.
 
* Bosch FR8DPP33+.
[[File:Spark_Plug_Bosch_FR8DPP33+.JPG|thumb|none|BOSCH FR8DPP33+.]]
 
* Denso 3275 PK16PR-L11 (EUR 8).
* NGK 4292 PFR5R-11 (EUR 8).
* BRISK DR17YS-9 specially suited for [[Liquefied Petroleum Gas (LPG)]] (EUR 3).
* [https://www.ngk.de/fileadmin/Dokumente/EN/Brosch%C3%BCren/Broschuere_LPG_12_Seiten_GB.pdf NGK LPG1 1496] - iridium spark plug specially suited for [[Liquefied Petroleum Gas (LPG)]].
 
===Service===
* M-B specifies replacement of plugs at every 100,000Km or 4 Years. Spark plug HT wires don't last much longer than that either.
* The resistance of the spark plug (electrode to HT connector) is about 4.5K to 6K ohms.
* There should be extremely high  resistance between the electrode and the plug metal thread.
* Set the spark plug electrode gap to 0.039” or 1mm.
* Tightening torque 15 - 22 ftlbs or 20 - 30Nm.
 
===Issues===
* Old spark plugs can show worn electrodes and a wider than specification gap.
* Broken insulators are common during removal of seized OEM plugs.
* Fouled spark plugs.
* Corroded spark plug threads make it difficult to remove an old plug. Solution is to use high temperature anti-seize grease available from autoparts stores when re-installing new plugs.


==Ignition Coils==
The W220 uses a twin-spark ignition system for each cylinder and thus the V8 has eight ignition coils (or ignition plug packs).
The W220 uses a twin-spark ignition system for each cylinder and thus the V8 has eight ignition coils (or ignition plug packs).
There is one coil pack per cylinder, which produces spark for two spark plugs per cylinder.


[[File:W220_WIS_Diagram_Showing_Spark_Plug_Pack_Annotations.JPG|600px]]
Misfiring frequently occurs because of burnt ignition coils, faulty ignition cables and spark plugs. These elements have to be replaced regularly.
 
It is possible to perform basic tests on an ignition coil using a digital multi meter (DMM).
 
Each coil secondary resistance measured from the plug cable to any of the three pins in the input electrical connector is approximately 4.8 M Ω (Mega Ohms).
 
The cable circuit is isolated from ground thus the resistance between the cable pin and ground is infinity Ohms or open circuit.


===Parts===
In case of failure, the following codes can be thrown:
* OE A0001587303 (replaced by A0001587803).
* P2050 Misfiring, Damages TWC (P0300) STORED
* BOSCH 0221503035 (40 EUR)
 
{|
|[[File:A0001587803_ignition_coil.jpg|thumb|none|Ignition coil (A0001587803).]]
|[[File:A0019907212_coil_pack_screw_T30.jpg|thumb|none|T30 screw for attaching ignition coil to engine (A0019907212).]]
|}
 
===Issues===
* Burnt coil.
* Cracked Pack.
 
[http://mbworld.org/forums/s-class-w220/431985-ongoing-maintenance-repair-2003-s600-2.html Article]
on fixing a burnt coil pack, right bank, on cylinder 4 which threw the following codes:
* P2050 Misfiring , Damages TWC (P0300) STORED
* P2056 Misfiring of cylinder 4, damages TWC (P0304) STORED
* P2056 Misfiring of cylinder 4, damages TWC (P0304) STORED
* P205B Misfiring of cylinder 8, damages TWC (P0308) STORED
* P205B Misfiring of cylinder 8, damages TWC (P0308) STORED


==Ignition Cables==
== Notes on avoiding damage to ignition system ==
===Parts===
<!-- AH15.10-P-0002-01D
The spark plug high tension (HT) wires come in sets of sixteen.
Notes on avoiding damage to ignition system
The resistance for new plug wire is approximately 2.18K ohms.
ENGINE 104, 111, 112, 113, 119, 120, 156, 271, 272
With gasoline injection and ignition system ME-SFI
-->


{|
''The main points:''
|[[File:W220_Spark_Plug_HT_Wire.JPG|thumb|none|Ignition cable.]]
* '''No tests such as holding an ignition HT Wire at a distance from ground and observing a spark must be performed.'''
|[[File:Bosch_Spark_Plug_Wire_Set.JPG|thumb|none|BOSCH spark plug wire set.]]
* '''Do not operate the ignition system at starting speed unless all of the HT Wires are connected.'''
|}
* '''Before working at cranking speed e.g. to check compression pressure, switch off ignition and disconnect Ignition Control Unit from 12V.'''


For a W220 with Engine Number: 113.960 xxxx the lengths of the spark plug wires are as follows:
Notes on avoiding damage to ignition system:
* Cylinder - 1, Ignition Coil Port - a; HT wire size - L.
* To avoid damage to control unit, only connect and disconnect the two connectors on control unit when ignition is switched off.
* Cylinder - 1, Ignition Coil Port - b; HT wire size - G.
* Terminal 1 of ignition coils must not be short-circuited to GND, e.g. as antitheft protection.
* Cylinder - 2, Ignition Coil Port - a; HT wire size - H.
* Only install original ignition system components.
* Cylinder - 2, Ignition Coil Port - b; HT wire size - G.
* Do not operate ignition system at starting speed unless all of the ignition cables are connected.
* Cylinder - 3, Ignition Coil Port - a; HT wire size - K.
* No tests such as holding ignition cable 4 at a distance to GND, unplugging a spark plug connector or pulling cable 4 out of the ignition coils, may be performed at starting speed or when the engine is running.
* Cylinder - 3, Ignition Coil Port - b; HT wire size - G.
* Every high voltage circuit must be loaded with at least 2 kΩ (spark-plug connector).
* Cylinder - 4, Ignition Coil Port - a; HT wire size - K.
* If it is necessary to test the ignition spark when providing roadside assistance, this must only be done with a spark plug at a cylinder ignition cable. Ensure that spark plug has good contact to ground.
* Cylinder - 4, Ignition Coil Port - b; HT wire size - G.
* Before working at cranking speed, e.g. checking compression pressure, switch off ignition and disconnect connector "2" from control unit.
* Cylinder - 5, Ignition Coil Port - a; HT wire size - H.
* Cylinder - 5, Ignition Coil Port - b; HT wire size - G.
* Cylinder - 6, Ignition Coil Port - a; HT wire size - K.
* Cylinder - 6, Ignition Coil Port - b; HT wire size - G.
* Cylinder - 7, Ignition Coil Port - a; HT wire size - G.
* Cylinder - 7, Ignition Coil Port - b; HT wire size - G.
* Cylinder - 8, Ignition Coil Port - a; HT wire size - G.
* Cylinder - 8, Ignition Coil Port - b; HT wire size - K.
 
Where HT Wire Sizes (Tip to Tip) are (NB not in length sequence.):
* G: 245mm - x9 A1121500118 (45 EUR), BOSCH 0356912948 (14 EUR)
* K: 265mm - x4 A1121500218 (45 EUR), BOSCH 0356912950 (14 EUR)
* H: 290mm - x2 A1121500318 (56 EUR), BOSCH 0356912952 (30 EUR)
* L: 315mm - x1 A1121500418 (56 EUR), BOSCH 0356912954 (32 EUR)
 
Cable kits:
* HITACHI 134779
* NGK 7800 (221 EUR)
* MAGNETI MARELLI 941318111285 (80 EUR)
 
===Issues===
* Spark HT wires have a limited life.
* The resistance element in the HT wires often fails or goes high resistance due to fatigue.
* HT lead insulation can break down causing arcing to ground.
* A special spark plug wire removal tool is available. It is a 17mm, open ended tool with a 25mm off-set and is made by JTC with part number J-1308.  It can be found in eBay for $20.
 
==Tools==
 
[[File:JTC_Spark_Plug_Wire_Removal_Tool_J-1308.JPG|thumb|none|JTC Spark Plug Wire Removal Tool J-1308.]]
 
 
A regular 5/8" (15.8mm) spark plug socket with a rubber insert works well for removing spark plugs. However the secret is to use a variety of extensions e.g., a short 74mm 3/8" drive extension on the tight spots in conjunction with a with swivel head.
 
[[File:W220_Swivel_Extension_and_Spark_Plug_Socket.JPG|thumb|none|Swivel extension and spark plug socket.]]
 
==DIY Procedures==
===Replacing spark plugs and ignition wires===
<!-- http://www.benzworld.org/forums/w220-s-class/1598302-05-s500-spark-plug-replacement-video.html -->
{|
|{{#ev:youtube|https://www.youtube.com/watch?v=eycUkQ9T1V0|320|left|SPARK PLUGS AND WIRES REPLACEMENT|frame}}
|{{#ev:youtube|https://www.youtube.com/watch?v=qzCdqlpRN3g|320|left|How to replace spark plugs and wires|frame}}
|}
 
'''Summary of contributions at references.'''
 
* Step 1: Put Bonnet/Hood in Service Position
 
Push on the locks on the hinges at LH side and then the RH side and raise Bonnet/Hood to the Service Position.
 
* Step 2: Remove the Air Intake Tubes
* Step 3: Remove the Air Box
** Remove Front Cover.  First pull it up and slide it forward.
 
[[File:W220_Remove_Air_Box_Front_Cover.JPG|300px|center]]
** Pull the Air Box Back Cover forward and up.
 
[[File:W220_Remove_Air_Box_Back_Cover.JPG|300px|center]]
 
* Step 4: Remove Ignition Coil Packs and Spark Plug Wires
** Identify Ignition Coil Packs on the Valve Covers. Mark appropriately and do not mix them as the leads are different lengths.
 
[[File:W220_WIS_Diagram_Showing_Spark_Plug_Pack_Annotations.JPG|600px|center]]
 
[[File:W220_Ignition_Coil_Packs_and_HT_Wires.JPG|300px|center]]
 
** Unhook electrical connectors on Coil Packs by squeezing in tabs and pull straight up.
 
[[File:W220_Removing_Connectors_on_Ignition_Coil_Packs.JPG|300px|center]]
 
** Give the spark plug covers a slight tweak to rotate and loosen them a little first before attempting to lever them off.  Use special tool to remove plug leads.  When using a 17mm open ended spanner to pry off the spark plug covers, make sure you counter balance the leverage you're applying to ensure the cover comes off in line with the plug. Otherwise there's a tendency to push down on the cover which actually makes it very hard to remove.
** Remove T30 Bolts that hold down the coil packs on the valve cover. One T30 Bolt per coil pack.
 
[[File:W220_One_T30_Bolt_Per_Coil_Pack.JPG|300px|center]]
 
** Remove Coil Pack and keep in correct order as the wire lengths are all different. Do not mix them up. (Mark with masking tape.)
 
* Step 5: Remove Spark Plugs
** Use an air ratchet with a swivel extension and a 3/8" drive 5/8" spark plug socket.
 
[[File:W220_Swivel_Extension_and_Spark_Plug_Socket.JPG|300px|center]]
* Step 6: Add anti seize to new plug threads
** Add some hi-temp anti-seize compound to the plug threads before installing. Just a little dab will do.
* Step 7: Start New Plugs by Hand
** Use socket with extension and start new plugs by hand to avoid cross threading. [[File:W220_Start_New_Spark_Plugs_by_Hand.JPG|300px|center]]
 
* Step 8: Remove the Spark Plug Wires from Coil Packs
** Just twist the Spark Plug Wires and pull straight out to remove from Coil Packs.
* Step 9: Identify New Plug Wires
 
[[File:W220_Bosch_Ignition_Wire_Set.JPG|300px|center]]
 
** Carefully observe new spark plug wire annotations. Sixteen Spark Plug Wires are labelled ‘A’, ‘B’.... ’O’, ‘P’.
These are the ‘G’ and ‘L’ Wires. [[File:W220_‘G’_and_‘L’_Spark_Plug_Wires.JPG |300px|center]]
 
** Carefully observe new ignition coil pack annotations which are labelled on the top.
Eg this coil pack has ‘a’ and ‘b’ marked on the top. [[File:W220_Coil_Pack_marked_a_and_b.JPG|300px|center]]
 
** Carefully observe valve cover annotations. The Valve Cover also has Coil Pack and Plug Wire Annotations for each cylinder.
W220 Valve cover annotations cylinder 5 H goes to a and G goes to b. [[File:W220_Valve_cover_annotations_cylinder_5_H_goes_to_a_and_G_goes_to_b.JPG|300px|center]]
 
* Step 10: Install Plug Wires on Spark Plugs
** Put Plug Wires on before re-installing Coil Packs. Add dielectric grease or Silicon Spray to the plug end of the wires. This will make future plug changes easier and prevent any water problems.
** Use the Special Tool to put pressure on the plug wire to push it all the way on the plug.  Listen for a click as it goes on properly. [[File:W220_Reinstall_plugs_apply_pressure_and_listen_for_click.JPG|300px|center]]
 
* Step 11: Re-install Ignition Coil Packs
** Coil bolt is T-30, torque 71 in.lb. or 8Nm
 
==Tips==
* Most new spark plugs come pre-gapped and specify torque on the box.
* Always remove spark plugs on a stone cold engine or else risking stripping the threads.
* Ensure ignition wires "click" back onto new plugs or risk cylinder misfire.
* To save your back jack up the car front, or run up onto ramps the night before.
* Time saver tip - if valve and breather cover gaskets need to be refreshed, combine with the spark plug change out. Do one side each day over the weekend.


'''Use of testers and testing units:'''
* Only connect and disconnect secondary measuring sensor to corresponding ignition cables when vertical engine and ignition are switched off.
* If the short-circuit protection is operated (cylinder comparison) and the engine stays upright, it is not possible to conduct the test with this test instrument.
* Do not connect test lamp to ignition coil terminals 1 and 15.


== Remove/install ignition coils ==
== Remove/install ignition coils ==
Line 280: Line 118:
|[[File:W220_remove_install_ignition_coils.png]]
|[[File:W220_remove_install_ignition_coils.png]]
|}
|}


# Unclip cover on front side of engine
# Unclip cover on front side of engine
# Remove engine cover with integrated air filter. The air filter is integrated in the engine cover. Remove the engine cover or the air filter housing by pulling it from the cylinder head covers vertically in the upward direction.
# Remove engine cover with integrated air filter. The air filter is integrated in the engine cover. Remove the engine cover or the air filter housing by pulling it from the cylinder head covers vertically in the upward direction.
# Remove air filter housing.
# Remove air filter housing.
# Remove screw (5/3)
# Remove screw (5/3). ''Remove Torx 30 bolts that hold down the coil packs on the valve cover. One T30 bolt per ignition coil.''
# Detach spark plug connector (5/1) from the spark plugs. Pry off spark plug connector (5/1) using open-end wrench, double over the cylinder head cover of the spark plugs. Installation: Observe the identification of the connector (arrow) on the cylinder head cover and the ignition coil of cylinders 1 to 6 or 1 to 8 for the corresponding spark plug connector (5/1).
# Detach spark plug connector (5/1) from the spark plugs. Pry off spark plug connector (5/1) using open-end wrench, double over the cylinder head cover of the spark plugs. Installation: Observe the identification of the connector (arrow) on the cylinder head cover and the ignition coil of cylinders 1 to 6 or 1 to 8 for the corresponding spark plug connector (5/1). ''Installing: put pressure on the ignition cable connector to push it all the way on the plug. Listen for a click as it goes on properly.''
# Separate electrical connector of ignition coil of cylinder 1 to 6 (T1/1 to T1/6) or 1 to 8 (T1/1 to T1/8). Installation: Install new cable ties.
# Separate electrical connector of ignition coil of cylinder 1 to 6 (T1/1 to T1/6) or 1 to 8 (T1/1 to T1/8). Installation: Install new cable ties.
# Remove ignition coil of cylinder 1 to 6 (T1/1 to T1/6) or 1 to 8 (T1/1 to T1/8)
# Remove ignition coil of cylinder 1 to 6 (T1/1 to T1/6) or 1 to 8 (T1/1 to T1/8)
Line 294: Line 131:
* Bolt, ignition coil to cylinder head cover (Engine 112, 113): 8 Nm
* Bolt, ignition coil to cylinder head cover (Engine 112, 113): 8 Nm


[[File:Open_ended_wrench_double_110589010100.png|thumb|none|Open-end wrench, double (110 589 01 01 00)]]
''A special spark plug cable removal tool is available (110 589 01 01 00). It is a 17mm, open ended tool with a 25mm off-set and is made by JTC with part number J-1308. It can be found in eBay for $20.''
{|
|[[File:Open_ended_wrench_double_110589010100.png|thumb|none|Open-end wrench, double (110 589 01 01 00)]]
|[[File:JTC_Spark_Plug_Wire_Removal_Tool_J-1308.JPG|thumb|none|JTC Spark Plug Wire Removal Tool J-1308.]]
|}


== Replace spark plugs ==
== Replace spark plugs ==
Line 339: Line 180:
|}
|}


# Remove ignition coils
# ''Put hood in service position. Push on the locks on the hinges at left side and then the right side and raise hood to the service position (90 degrees fully open).''
# Remove ignition coils. ''Keep in correct order as the wire lengths are all different. Do not mix them up (mark with masking tape).''
# Blow out any dirt residue in the spark-plug recesses using compressed air
# Blow out any dirt residue in the spark-plug recesses using compressed air
# Remove spark plugs (1) using spark plug wrench (01) from cylinder heads
# Remove spark plugs (1) using spark plug wrench (01) from cylinder heads. ''Use an air ratchet with a swivel extension and a 3/8" drive 5/8" spark plug socket.''
# Screw new spark plugs (1) using spark plug wrench (01) into cylinder heads.
# Screw new spark plugs (1) using spark plug wrench (01) into cylinder heads. ''Start screwing new spark plugs by hand to avoid cross threading.''
# Check spark plug connector (2), ignition coils and ignition lines for damage, deformation and crack formation.
# Check spark plug connector (2), ignition coils and ignition lines for damage, deformation and crack formation.
# Grease rubber lips (3) of spark plug connectors (2) with spark plug connector grease (A0029898051) before installing
# Grease rubber lips (3) of spark plug connectors (2) with spark plug connector grease (A0029898051) before installing
# Install ignition coils
# Install ignition coils
''Always remove spark plugs on a stone cold engine or else risking stripping the threads.''


Torque specifications:
Torque specifications:
* Spark plugs (engine 112 and 113): 28 Nm
* Spark plugs (engine 112 and 113): 28 Nm
{|
|[[File:W220_‘G’_and_‘L’_Spark_Plug_Wires.JPG|thumb|none|Cable length symbol on ignition cable connectors.]]
|[[File:W220_Valve_cover_annotations_cylinder_5_H_goes_to_a_and_G_goes_to_b.JPG|thumb|none|The valve cover has ignition coil and ignition cable annotations for each cylinder (cylinder 5 H-cable goes to ''a'' and G-cable goes to ''b'').]]
|[[File:W220_Swivel_Extension_and_Spark_Plug_Socket.JPG|thumb|none|Swivel extension and spark plug socket. A regular 5/8" (15.8mm) spark plug socket with a rubber insert works well for removing spark plugs. However the secret is to use a variety of extensions e.g., a short 74mm 3/8" drive extension on the tight spots in conjunction with a with swivel head.]]
|}
<!-- http://www.benzworld.org/forums/w220-s-class/1598302-05-s500-spark-plug-replacement-video.html -->
{|
|{{#ev:youtube|https://www.youtube.com/watch?v=eycUkQ9T1V0|320|left|SPARK PLUGS AND WIRES REPLACEMENT|frame}}
|{{#ev:youtube|https://www.youtube.com/watch?v=qzCdqlpRN3g|320|left|How to replace spark plugs and wires|frame}}
|}


== Spark plug connector grease ==
== Spark plug connector grease ==
Line 367: Line 224:
|[[File:Permatex_22058_Dielectric_Tune-Up_Grease.JPG|thumb|none|Permatex 22058 Dielectric Tune-Up Grease]]
|[[File:Permatex_22058_Dielectric_Tune-Up_Grease.JPG|thumb|none|Permatex 22058 Dielectric Tune-Up Grease]]
|}
|}
== Parts ==
=== Spark plugs ===
* Mercedes-Benz specifies replacement of plugs at every 100 000km or 4 years. Spark plug ignition cables don't last much longer than that either.
* The resistance of the spark plug (electrode to ignition cable connector) is about 4.5K to 6K ohms.
* There should be extremely high resistance between the electrode and the plug metal thread.
* The spark plug electrode gap is 0.039” or 1mm.
* Tightening torque for spark plugs is 20-30 Nm (28 Nm according to WIS).
* Old spark plugs can show worn electrodes and a wider than specification gap.
* Broken insulators are common during removal of seized OEM plugs.
* Corroded spark plug threads make it difficult to remove an old plug. Solution is to use high temperature anti-seize grease (see below) when re-installing new plugs.
Part numbers:
* OE - A0041591903
* OE - A0031599403
* OE - A0041595003 (15 EUR)
* Bosch 0242230500 (5 EUR)
* Denso PK16PRL11 (6 EUR)
* Denso IK16TT (8 EUR) - recommended for [[LPG]], up to 100 0000 km
* NGK 4292 (EUR 8)
* BRISK DR17YS-9 (EUR 3) - suited for [[LPG]], interval max 30 000 km
[[File:Spark_Plug_Bosch_FR8DPP33+.JPG|thumb|none|BOSCH 0242230500]]
=== Ignition coils ===
* It is possible to perform basic tests on an ignition coil using a digital multi meter (DMM). Each coil secondary resistance measured from the plug cable to any of the three pins in the input electrical connector is approximately 4.8 M Ω (Mega Ohms). The cable circuit is isolated from ground thus the resistance between the cable pin and ground is infinity Ohms or open circuit.
<!--
[http://mbworld.org/forums/s-class-w220/431985-ongoing-maintenance-repair-2003-s600-2.html Article]
on fixing a burnt coil pack, right bank, on cylinder 4 which threw the following codes:
* P2050 Misfiring , Damages TWC (P0300) STORED
* P2056 Misfiring of cylinder 4, damages TWC (P0304) STORED
* P205B Misfiring of cylinder 8, damages TWC (P0308) STORED
-->
* OE A0001587303 (replaced by A0001587803).
* BOSCH 0221503035 (40 EUR)
{|
|[[File:A0001587803_ignition_coil.jpg|thumb|none|Ignition coil (A0001587803)]]
|[[File:A0019907212_coil_pack_screw_T30.jpg|thumb|none|T30 screw for attaching ignition coil to engine (A0019907212).]]
|}
=== Ignition cables ===
* Spark plug ignition cables have a limited life. The resistance element in the cables often fails or goes high resistance due to fatigue.
Cable lead insulation can break down causing arcing to ground. The resistance for new plug wire is approximately 2.18K ohms.
* It is possible to perform basic tests on an ignition coil using a digital multi meter (DMM). Each coil secondary resistance measured from the plug cable to any of the three pins in the input electrical connector is approximately 4.8 M Ω (Mega Ohms). The cable circuit is isolated from ground thus the resistance between the cable pin and ground is infinity Ohms or open circuit.
<!--
[http://mbworld.org/forums/s-class-w220/431985-ongoing-maintenance-repair-2003-s600-2.html Article]
on fixing a burnt coil pack, right bank, on cylinder 4 which threw the following codes:
* P2050 Misfiring , Damages TWC (P0300) STORED
* P2056 Misfiring of cylinder 4, damages TWC (P0304) STORED
* P205B Misfiring of cylinder 8, damages TWC (P0308) STORED
-->
Ignition cables are in different lengths:
* G-cable: 245mm - A1121500118 (45 EUR), BOSCH 0356912948 (14 EUR) - M112 x8, M113 x9
* K-cable: 265mm - A1121500218 (45 EUR), BOSCH 0356912950 (14 EUR) - M112 x4, M113 x4
* H-cable: 290mm - A1121500318 (56 EUR), BOSCH 0356912952 (30 EUR) - M112 x0, M113 x2
* L-cable: 315mm - A1121500418 (56 EUR), BOSCH 0356912954 (32 EUR) - M112 x0, M113 x1
{|
|[[File:W220_Spark_Plug_HT_Wire.JPG|thumb|none|Ignition cable.]]
|[[File:Bosch_Spark_Plug_Wire_Set.JPG|thumb|none|BOSCH spark plug wire set for M113.]]
|}
Ignition cable lengths for M112 (V6 [[S350]]):
* Cylinder 1, port a; K-cable
* Cylinder 1, port b; G-cable
* Cylinder 2, port a; G-cable
* Cylinder 2, port b; G-cable
* Cylinder 3, port a; G-cable
* Cylinder 3, port b; K-cable
* Cylinder 4, port a; K-cable
* Cylinder 4, port b; G-cable
* Cylinder 5, port a; G-cable
* Cylinder 5, port b; G-cable
* Cylinder 6, port a; G-cable
* Cylinder 6, port b; K-cable
Ignition cable lengths for M113 (V8 [[S430]] and [[S500]]):
* Cylinder 1, port a; L-cable
* Cylinder 1, port b; G-cable
* Cylinder 2, port a; H-cable
* Cylinder 2, port b; G-cable
* Cylinder 3, port a; K-cable
* Cylinder 3, port b; G-cable
* Cylinder 4, port a; K-cable
* Cylinder 4, port b; G-cable
* Cylinder 5, port a; H-cable
* Cylinder 5, port b; G-cable
* Cylinder 6, port a; K-cable
* Cylinder 6, port b; G-cable
* Cylinder 7, port a; G-cable
* Cylinder 7, port b; G-cable
* Cylinder 8, port a; G-cable
* Cylinder 8, port b; K-cable
Cable kits:
* Valeo 346141 (130 EUR)- M112
* NGK 7800 (221 EUR) - M113
* MAGNETI MARELLI 941318111285 (80 EUR) - M113

Revision as of 18:00, 19 July 2021

Ignition System

Parts in EPC related to ignition system.

This page covers W220 petrol engines M112 (V6 engine used in S350) and M113 (V8 engine used in S430 and S500).

The W220 uses a twin-spark ignition system for each cylinder and thus the V8 has eight ignition coils (or ignition plug packs). There is one coil pack per cylinder, which produces spark for two spark plugs per cylinder.

Misfiring frequently occurs because of burnt ignition coils, faulty ignition cables and spark plugs. These elements have to be replaced regularly.

In case of failure, the following codes can be thrown:

  • P2050 Misfiring, Damages TWC (P0300) STORED
  • P2056 Misfiring of cylinder 4, damages TWC (P0304) STORED
  • P205B Misfiring of cylinder 8, damages TWC (P0308) STORED

Notes on avoiding damage to ignition system

The main points:

  • No tests such as holding an ignition HT Wire at a distance from ground and observing a spark must be performed.
  • Do not operate the ignition system at starting speed unless all of the HT Wires are connected.
  • Before working at cranking speed e.g. to check compression pressure, switch off ignition and disconnect Ignition Control Unit from 12V.

Notes on avoiding damage to ignition system:

  • To avoid damage to control unit, only connect and disconnect the two connectors on control unit when ignition is switched off.
  • Terminal 1 of ignition coils must not be short-circuited to GND, e.g. as antitheft protection.
  • Only install original ignition system components.
  • Do not operate ignition system at starting speed unless all of the ignition cables are connected.
  • No tests such as holding ignition cable 4 at a distance to GND, unplugging a spark plug connector or pulling cable 4 out of the ignition coils, may be performed at starting speed or when the engine is running.
  • Every high voltage circuit must be loaded with at least 2 kΩ (spark-plug connector).
  • If it is necessary to test the ignition spark when providing roadside assistance, this must only be done with a spark plug at a cylinder ignition cable. Ensure that spark plug has good contact to ground.
  • Before working at cranking speed, e.g. checking compression pressure, switch off ignition and disconnect connector "2" from control unit.

Use of testers and testing units:

  • Only connect and disconnect secondary measuring sensor to corresponding ignition cables when vertical engine and ignition are switched off.
  • If the short-circuit protection is operated (cylinder comparison) and the engine stays upright, it is not possible to conduct the test with this test instrument.
  • Do not connect test lamp to ignition coil terminals 1 and 15.

Remove/install ignition coils

Shown on engine 112
  • 5/1 - Spark plug connector
  • 5/3 - Screw
  • T1/1 - Cylinder 1 ignition coil
  • T1/2 - Cylinder 2 ignition coil
  • T1/3 - Cylinder 3 ignition coil
  • T1/4 - Cylinder 4 ignition coil
  • T1/5 - Cylinder 5 ignition coil
  • T1/6 - Cylinder 6 ignition coil
  • T1/7 - Cylinder 7 ignition coil
  • T1/8 - Cylinder 8 ignition coil

Arrow: Identification of the connector

  1. Unclip cover on front side of engine
  2. Remove engine cover with integrated air filter. The air filter is integrated in the engine cover. Remove the engine cover or the air filter housing by pulling it from the cylinder head covers vertically in the upward direction.
  3. Remove air filter housing.
  4. Remove screw (5/3). Remove Torx 30 bolts that hold down the coil packs on the valve cover. One T30 bolt per ignition coil.
  5. Detach spark plug connector (5/1) from the spark plugs. Pry off spark plug connector (5/1) using open-end wrench, double over the cylinder head cover of the spark plugs. Installation: Observe the identification of the connector (arrow) on the cylinder head cover and the ignition coil of cylinders 1 to 6 or 1 to 8 for the corresponding spark plug connector (5/1). Installing: put pressure on the ignition cable connector to push it all the way on the plug. Listen for a click as it goes on properly.
  6. Separate electrical connector of ignition coil of cylinder 1 to 6 (T1/1 to T1/6) or 1 to 8 (T1/1 to T1/8). Installation: Install new cable ties.
  7. Remove ignition coil of cylinder 1 to 6 (T1/1 to T1/6) or 1 to 8 (T1/1 to T1/8)
  8. Install in the reverse order

Torque specification:

  • Bolt, ignition coil to cylinder head cover (Engine 112, 113): 8 Nm

A special spark plug cable removal tool is available (110 589 01 01 00). It is a 17mm, open ended tool with a 25mm off-set and is made by JTC with part number J-1308. It can be found in eBay for $20.

Open-end wrench, double (110 589 01 01 00)
JTC Spark Plug Wire Removal Tool J-1308.

Replace spark plugs

Shown on engine 112 in model 210
  • 01 - Spark plug wrench
  • 1 - Spark plug
Shown on ignition coil of engine 157.980
  • 2 - Spark plug connector
  • 3 - Rubber lip
  1. Put hood in service position. Push on the locks on the hinges at left side and then the right side and raise hood to the service position (90 degrees fully open).
  2. Remove ignition coils. Keep in correct order as the wire lengths are all different. Do not mix them up (mark with masking tape).
  3. Blow out any dirt residue in the spark-plug recesses using compressed air
  4. Remove spark plugs (1) using spark plug wrench (01) from cylinder heads. Use an air ratchet with a swivel extension and a 3/8" drive 5/8" spark plug socket.
  5. Screw new spark plugs (1) using spark plug wrench (01) into cylinder heads. Start screwing new spark plugs by hand to avoid cross threading.
  6. Check spark plug connector (2), ignition coils and ignition lines for damage, deformation and crack formation.
  7. Grease rubber lips (3) of spark plug connectors (2) with spark plug connector grease (A0029898051) before installing
  8. Install ignition coils

Always remove spark plugs on a stone cold engine or else risking stripping the threads.


Torque specifications:

  • Spark plugs (engine 112 and 113): 28 Nm
Cable length symbol on ignition cable connectors.
The valve cover has ignition coil and ignition cable annotations for each cylinder (cylinder 5 H-cable goes to a and G-cable goes to b).
Swivel extension and spark plug socket. A regular 5/8" (15.8mm) spark plug socket with a rubber insert works well for removing spark plugs. However the secret is to use a variety of extensions e.g., a short 74mm 3/8" drive extension on the tight spots in conjunction with a with swivel head.
Load video
YouTube
SPARK PLUGS AND WIRES REPLACEMENT
Load video
YouTube
How to replace spark plugs and wires

Spark plug connector grease

The rubber boot on the ignition cable is difficult to remove from a spark plug even when using the special removal tool. Solution is to apply a small quantity of dielectric grease to the top conductor and the ceramic insulator (or to the spark plug connector) when re-installing new plugs. This helps keep moisture away and stops corrosion. Makes it infinitely easier to remove the spark plug connector.

  • OE - A0029898051 (12 EUR)
  • BERU ZKF01 - 0890300029 (8 EUR)
  • Permatex 22058
Grease for spark plug adaptors (0029898051)
]BERU ZKF01 grease for spark plug adaptors
]BERU ZKF01 grease for spark plug adaptors
Permatex 22058 Dielectric Tune-Up Grease

Parts

Spark plugs

  • Mercedes-Benz specifies replacement of plugs at every 100 000km or 4 years. Spark plug ignition cables don't last much longer than that either.
  • The resistance of the spark plug (electrode to ignition cable connector) is about 4.5K to 6K ohms.
  • There should be extremely high resistance between the electrode and the plug metal thread.
  • The spark plug electrode gap is 0.039” or 1mm.
  • Tightening torque for spark plugs is 20-30 Nm (28 Nm according to WIS).
  • Old spark plugs can show worn electrodes and a wider than specification gap.
  • Broken insulators are common during removal of seized OEM plugs.
  • Corroded spark plug threads make it difficult to remove an old plug. Solution is to use high temperature anti-seize grease (see below) when re-installing new plugs.

Part numbers:

  • OE - A0041591903
  • OE - A0031599403
  • OE - A0041595003 (15 EUR)
  • Bosch 0242230500 (5 EUR)
  • Denso PK16PRL11 (6 EUR)
  • Denso IK16TT (8 EUR) - recommended for LPG, up to 100 0000 km
  • NGK 4292 (EUR 8)
  • BRISK DR17YS-9 (EUR 3) - suited for LPG, interval max 30 000 km
BOSCH 0242230500

Ignition coils

  • It is possible to perform basic tests on an ignition coil using a digital multi meter (DMM). Each coil secondary resistance measured from the plug cable to any of the three pins in the input electrical connector is approximately 4.8 M Ω (Mega Ohms). The cable circuit is isolated from ground thus the resistance between the cable pin and ground is infinity Ohms or open circuit.
  • OE A0001587303 (replaced by A0001587803).
  • BOSCH 0221503035 (40 EUR)
Ignition coil (A0001587803)
T30 screw for attaching ignition coil to engine (A0019907212).

Ignition cables

  • Spark plug ignition cables have a limited life. The resistance element in the cables often fails or goes high resistance due to fatigue.

Cable lead insulation can break down causing arcing to ground. The resistance for new plug wire is approximately 2.18K ohms.

  • It is possible to perform basic tests on an ignition coil using a digital multi meter (DMM). Each coil secondary resistance measured from the plug cable to any of the three pins in the input electrical connector is approximately 4.8 M Ω (Mega Ohms). The cable circuit is isolated from ground thus the resistance between the cable pin and ground is infinity Ohms or open circuit.

Ignition cables are in different lengths:

  • G-cable: 245mm - A1121500118 (45 EUR), BOSCH 0356912948 (14 EUR) - M112 x8, M113 x9
  • K-cable: 265mm - A1121500218 (45 EUR), BOSCH 0356912950 (14 EUR) - M112 x4, M113 x4
  • H-cable: 290mm - A1121500318 (56 EUR), BOSCH 0356912952 (30 EUR) - M112 x0, M113 x2
  • L-cable: 315mm - A1121500418 (56 EUR), BOSCH 0356912954 (32 EUR) - M112 x0, M113 x1
Ignition cable.
BOSCH spark plug wire set for M113.

Ignition cable lengths for M112 (V6 S350):

  • Cylinder 1, port a; K-cable
  • Cylinder 1, port b; G-cable
  • Cylinder 2, port a; G-cable
  • Cylinder 2, port b; G-cable
  • Cylinder 3, port a; G-cable
  • Cylinder 3, port b; K-cable
  • Cylinder 4, port a; K-cable
  • Cylinder 4, port b; G-cable
  • Cylinder 5, port a; G-cable
  • Cylinder 5, port b; G-cable
  • Cylinder 6, port a; G-cable
  • Cylinder 6, port b; K-cable

Ignition cable lengths for M113 (V8 S430 and S500):

  • Cylinder 1, port a; L-cable
  • Cylinder 1, port b; G-cable
  • Cylinder 2, port a; H-cable
  • Cylinder 2, port b; G-cable
  • Cylinder 3, port a; K-cable
  • Cylinder 3, port b; G-cable
  • Cylinder 4, port a; K-cable
  • Cylinder 4, port b; G-cable
  • Cylinder 5, port a; H-cable
  • Cylinder 5, port b; G-cable
  • Cylinder 6, port a; K-cable
  • Cylinder 6, port b; G-cable
  • Cylinder 7, port a; G-cable
  • Cylinder 7, port b; G-cable
  • Cylinder 8, port a; G-cable
  • Cylinder 8, port b; K-cable

Cable kits:

  • Valeo 346141 (130 EUR)- M112
  • NGK 7800 (221 EUR) - M113
  • MAGNETI MARELLI 941318111285 (80 EUR) - M113
Retrieved from "https://w220.wiki/index.php?title=Ignition_system&oldid=8252"