Rear seats: Difference between revisions
| Line 35: | Line 35: | ||
There are two push buttons under the bottom lip of the leather where it meets the floor carpet - run your fingers along until you feel the recess and just push it in. Do this on both sides of the car, and the bench can be lifted out. | There are two push buttons under the bottom lip of the leather where it meets the floor carpet - run your fingers along until you feel the recess and just push it in. Do this on both sides of the car, and the bench can be lifted out. | ||
== Remove/install rear seat cushion (CODE 223b) == | |||
<!-- AR91.12-P-1020M Remove/install rear seat cushion | |||
MODEL 220.0 /1 with CODE (223b) Electrically adjustable rear bench seat | |||
MODELS 220.875 /878 vis-à-vis seats | |||
30.1.98 --> | |||
{| | |||
|[[File:W220_remove_install_rear_seat_cushion.jpg]] | |||
| | |||
* 1 - Springs for seat locking mechanism | |||
* 2 - Pins for locating rear seat cushion | |||
* 3 - Electrical connector for heated seats | |||
* 4 - Rear seat cushion | |||
* 5 - Electrical connector for seat ventilation | |||
|} | |||
# Move rear seat cushion (4) fully forwards | |||
# Press springs (1) below the rear seat cushion (4) outwards and remove seat cushion. Installation: Ensure that the pins (2) on the seat adjuster move in the guides on the seat. | |||
# Disconnect electrical connector for heated seats (3) (with electric heated seats for left and right rear seat, code 872). | |||
# Disconnect electrical connector of seat ventilation (5) and heated seats (with seat ventilation for rear seats, code 402a). | |||
# Install in the reverse order | |||
Revision as of 20:54, 18 April 2017
Rear seat adjustment
In vehicles equipped with option code ?? the switch can be used to adjust rear head restraint.
In vehicles equipped with option code ?? the switches can be used to adjust rear:
- (1) Seat bench fore and aft adjustment
- (2) Head restraint fold/place upright
In vehicles equipped with option code ?? the switches can be used to adjust rear:
- (1) Seat fore and aft adjustment
- (2) Seat height
- (3) Head restraint fold/place upright
Front passenger seat adjustment from rear
Vehicles equipped with option code 247 have two additional buttons (buttons (1) and (2)) on the rear DCM behind front passenger seat, which can be used to adjust front passenger seat.
None: Adjusting the passenger seat position from the rear is not possible if you deactivate the operation of the rear door windows (override switch in driver's door).
Remove Rear Seat Backrest
Lower the head restraints. There are 2 torx bolts at the bottom of the backrest - remove these and if the car doesn’t have electrical rear seats, lift the backrest up about an inch and pull it right out. With electrical rear seats the centre seat squab and back-rest must be removed to expose two Torx screws securing the left and right rear back-rests at the centre top.
Remove Rear Seat Bench
There are two push buttons under the bottom lip of the leather where it meets the floor carpet - run your fingers along until you feel the recess and just push it in. Do this on both sides of the car, and the bench can be lifted out.
Remove/install rear seat cushion (CODE 223b)
|
|
- Move rear seat cushion (4) fully forwards
- Press springs (1) below the rear seat cushion (4) outwards and remove seat cushion. Installation: Ensure that the pins (2) on the seat adjuster move in the guides on the seat.
- Disconnect electrical connector for heated seats (3) (with electric heated seats for left and right rear seat, code 872).
- Disconnect electrical connector of seat ventilation (5) and heated seats (with seat ventilation for rear seats, code 402a).
- Install in the reverse order