Bumpers: Difference between revisions

From W220 S-Class Encyclopedia
Jump to navigation Jump to search
(embed youtube videos)
 
(4 intermediate revisions by the same user not shown)
Line 1: Line 1:
==Remove/install front bumper==
<!--
AR88.20-P-2000M, Remove/install front bumper, 11.6.97
MODEL 215.373 /374 /375 /376 /378 /379
MODEL 220.025 /026 /028 /063 /065 /070 /073 /075 /125 /128 /165 /170 /173 /175 /176 /178 /179 /875 /878
-->
{|
|[[File:W220_Remove_install_front_bumper.jpg]]
|
* 1 - Bumper
* 1 A - Foam insert
* 1 B - Retaining plate
* 2 - Bolt
* 3 - Nut
* 11 - Antenna line
|}
{|
|[[File:W220_Remove_install_front_bumper_2.jpg]]
|
* 4 - Air inlet grille
* 5 - Bracket
* 6 - Bolt
* 7 - Retaining bracket
* B14 - Outside temperature display temperature sensor
* X26/27 - Front bumper PTS connector
|}
# Expose antenna line (11) for TV antenna
# Electrical plug socket in left fuse box. Installation: Install new tie straps.
# Engine 112, 113, 137, 275:
## Remove bottom engine compartment paneling. Only remove front part.
# Engine 613, 628, 648:
## Remove bottom part of noise encapsulation. Only remove front part.
# Pull outside temperature display temperature sensor (B14) out of bumper
# Unlock and separate front bumper PTS connector (X26/27). To unlock, pivot lock flap in direction of arrow.
# Remove fender liner from front fender. Remove only front section of fender liner.
# Unscrew bolt (6)
# Pivot retaining bracket (7) toward center of vehicle, pull out to rear and remove
# Unscrew bolt (2)
# Unclip air inlet grate (4). Do not damage paint.
# Unscrew nuts (3).
# Remove bumper (1) toward front. Installation: Ensure that retainer tabs on rear bumper (1) are pushed behind bracket (5).
# Install in the reverse order
{|
|[[File:W220_temperature_sensor_inside_bumper.jpg|thumb|none|Outside temperature sensor (B14).]]
|[[File:W220_temperature_sensor_removed.jpg|thumb|none|Sensor unplugged.]]
|[[File:W220_temperature_sensor_bumper_hole.jpg|thumb|none|Sensor hole in the left bumper grille ([[facelift]]).]]
|}
{|
|[[File:W220_bumper_fender_screw.jpg|thumb|none|Screw holding retaining bracket.]]
|[[File:W220_bumper_fender_retaining_bracket_look_from_inside.jpg|thumb|none|Look from right headlamp area.]]
|[[File:W220_bumper_fender_retaining_bracket_removed.jpg|thumb|none|Retaining bracket removed.]]
|}
[[File:W220_bumper_fender_detached.jpg|thumb|none|Bumper detached from fender.]]
==Bumper Strip Removal==
==Bumper Strip Removal==
{{#ev:youtube|https://www.youtube.com/watch?v=ZRZWV-lrqvA|320|center|W220 bumper strip front removal.|frame}}
{|
{{#ev:youtube|https://www.youtube.com/watch?v=J1BqqDaKSos|320|center|W220 bumper strip rear removal.|frame}}
|{{#ev:youtube|https://www.youtube.com/watch?v=ZRZWV-lrqvA|320|center|W220 bumper strip front removal.|frame}}
|{{#ev:youtube|https://www.youtube.com/watch?v=J1BqqDaKSos|320|center|W220 bumper strip rear removal.|frame}}
|}


== Facelift Model Bumpers==
== Facelift Model Bumpers==
Line 13: Line 75:
|[[File:W220_A2208851523_back.jpg|thumb|none|A2208851523 back.]]
|[[File:W220_A2208851523_back.jpg|thumb|none|A2208851523 back.]]
|[[File:W220_A2208851523_side.jpg|thumb|none|A2208851523 side.]]
|[[File:W220_A2208851523_side.jpg|thumb|none|A2208851523 side.]]
|}
=== Rear Bumper Trailer Cover ===
Part number A2208850423. Aftermarket parts sold at Aliexpress (10 EUR) fit well in practice.
{|
|[[File:Rear-Bumper-Tow-Hook-Cover-A2208850423_aftermarket.jpg|thumb|none|A2208850423 front]]
|[[File:Rear-Bumper-Tow-Hook-Cover-A2208850423_aftermarket_back.jpg|thumb|none|A2208850423 back]]
|}
|}


== Pre-facelift ==
== Pre-facelift ==

Latest revision as of 11:06, 8 August 2023

Remove/install front bumper

  • 1 - Bumper
  • 1 A - Foam insert
  • 1 B - Retaining plate
  • 2 - Bolt
  • 3 - Nut
  • 11 - Antenna line
  • 4 - Air inlet grille
  • 5 - Bracket
  • 6 - Bolt
  • 7 - Retaining bracket
  • B14 - Outside temperature display temperature sensor
  • X26/27 - Front bumper PTS connector
  1. Expose antenna line (11) for TV antenna
  2. Electrical plug socket in left fuse box. Installation: Install new tie straps.
  3. Engine 112, 113, 137, 275:
    1. Remove bottom engine compartment paneling. Only remove front part.
  4. Engine 613, 628, 648:
    1. Remove bottom part of noise encapsulation. Only remove front part.
  5. Pull outside temperature display temperature sensor (B14) out of bumper
  6. Unlock and separate front bumper PTS connector (X26/27). To unlock, pivot lock flap in direction of arrow.
  7. Remove fender liner from front fender. Remove only front section of fender liner.
  8. Unscrew bolt (6)
  9. Pivot retaining bracket (7) toward center of vehicle, pull out to rear and remove
  10. Unscrew bolt (2)
  11. Unclip air inlet grate (4). Do not damage paint.
  12. Unscrew nuts (3).
  13. Remove bumper (1) toward front. Installation: Ensure that retainer tabs on rear bumper (1) are pushed behind bracket (5).
  14. Install in the reverse order
Outside temperature sensor (B14).
Sensor unplugged.
Sensor hole in the left bumper grille (facelift).
Screw holding retaining bracket.
Look from right headlamp area.
Retaining bracket removed.
Bumper detached from fender.

Bumper Strip Removal

Load video
YouTube
W220 bumper strip front removal.
Load video
YouTube
W220 bumper strip rear removal.

Facelift Model Bumpers

Front Center Lower Grille

Part number A2208851523.

A2208851523 front.
A2208851523 back.
A2208851523 side.

Rear Bumper Trailer Cover

Part number A2208850423. Aftermarket parts sold at Aliexpress (10 EUR) fit well in practice.

A2208850423 front
A2208850423 back

Pre-facelift

Retrieved from "https://w220.wiki/index.php?title=Bumpers&oldid=8930"