Brakes: Difference between revisions

From W220 S-Class Encyclopedia
Jump to navigation Jump to search
(→‎Brake fluid replacement: updated instructions)
 
(30 intermediate revisions by 2 users not shown)
Line 3: Line 3:
[[File:W220_front_wheel_brake_epc.png|thumb|none|Front brake-related parts in [[EPC]]]]
[[File:W220_front_wheel_brake_epc.png|thumb|none|Front brake-related parts in [[EPC]]]]


=== Front dust shield ===
=== Front disk brake rotor ===
It is common for the dust shield (also known as protective plate) to rust in the bolt holes resulting in the dust shield touching disk rotor.
Front brake disks on vehicles with M113 engines (S430/S500) are larger and thicker compared to vehicles with M112 engines (S280/S320/S500).
For the front axle aftermarket dust shields are not available in the market.
{|
|
S500/S430:
* OE A2204212512 (135 EUR)
* ATE 24.0132-0115.1 (75 EUR/piece)
* TRW DF4148S (58 EUR/piece)


 
[[File:W220_front_brake_disk_TRW_DF4148S.jpg|thumb|none|TRW DF4148S brake disk (32mm thick, 330mm diameter)]]
[[File:W220_dust_shield_front_left_A2204200444.jpg|thumb|none|Dust shield front left (A2204200444)]]
|
 
S280/S320/S350:
Part numbers:
* OE left: A2204200444 (124 EUR)
* OE right: A2204200544 (124 EUR)
 
=== Front disk brake rotor ===
* OE A2204210912 (135 EUR)
* OE A2204210912 (135 EUR)
* TRW DF4149S (56 EUR)
* ATE 24.0128-0125.1 (69 EUR/piece)
 
* TRW DF4149S (56 EUR/piece)
[[File:W220_front_brake_disk_TRW_DF4149S.jpg|thumb|none|TRW DF4149S brake disk]]
[[File:W220_front_brake_disk_TRW_DF4149S.jpg|thumb|none|TRW DF4149S brake disk (28mm thick, 312mm diameter)]]
|}


=== Front disk brake pads ===
=== Front disk brake pads ===
Brake pads are sold in pairs (for both sides).
Brake pads are sold in pairs (for both sides).
* OE A0044209020 (112 EUR)
* OE A0044209020 (112 EUR)
* ATE 13.0470-4990.2 (67 EUR)
* TRW GDB1543DTE (50 EUR)
* TRW GDB1543DTE (50 EUR)


Line 28: Line 30:


=== Accessory kit ===
=== Accessory kit ===
In case brake pads are changed after several years, the spring bolts become seized and to remove them they have to be bent and broken out (see photo below).
When buying brake accessory kit, make sure to purchase spring that has bolt anchors (e.g., kit by ATE) to prevent spring from slipping off the bolts (see photos below).
{|
|[[File:W220_front_brake_removing_seized_spring_bolts.jpg|thumb|none|Removing seized spring bolts]]
|[[File:W220_front_brake_spring_slipped.jpg|thumb|none|Brake spring slipped off the bolts]]
|[[File:W220_front_brake_spring_attached.jpg|thumb|none|Brake spring with bolt anchors]]
|}


Part numbers:
* Spring - A0004217891 (replaced by A0004219791) (14 EUR)
* Spring - A0004217891 (replaced by A0004219791) (14 EUR)
* Bolts  - A0019915160 (12 EUR)
* Bolts  - A0019915160 (12 EUR)
* Kit - ATE 13.0460-0237.2 (9 EUR)
* Kit - ATE 13.0460-0237.2 (9 EUR)
[[File:W220_front_brakes_accessory_kit_ATE.jpg|thumb|none|ATE 13.0460-0237.2 accessory kit]]
{|
|[[File:W220_front_brakes_accessory_kit_ATE.jpg|thumb|none|ATE 13.0460-0237.2 accessory kit]]
|[[File:W220_front_brakes_accessory_kit_ATE_13.0460-0237.2.jpg|thumb|none|ATE 13.0460-0237.2 accessory kit]]
|}
 
=== Front dust shield ===
It is common for the dust shield (also known as a protective plate) to rust in the bolt holes resulting in the dust shield touching disk rotor.
The original dust shields are quote expensive, unfortunately, aftermarket dust shields for the front axle are not available in the market.
 
{|
|[[File:W220_front_dust_shield_rusted_bolt_holes_fixed.jpg|thumb|none|Rusted bolt holes fixed by installing large washers]]
|}
 
Part numbers:
* OE left: A2204200444 (124 EUR)
* OE right: A2204200544 (88 EUR)
 
{|
|[[File:W220_dust_shield_front_left_A2204200444.jpg|thumb|none|Dust shield front left (A2204200444)]]
|}


== Remove/install brake disc (front axle) ==
=== Remove/install brake disc (front axle) ===
<!-- AR42.10-P-0220I Remove/install brake disc 8.12.11
<!-- AR42.10-P-0220I Remove/install brake disc 8.12.11
MODEL 215, 220 -->
MODEL 215, 220 -->
Line 70: Line 100:
[[File:W220_rear_wheel_brake_epc.png|thumb|none|Rear brake-related parts in [[EPC]]]]
[[File:W220_rear_wheel_brake_epc.png|thumb|none|Rear brake-related parts in [[EPC]]]]


=== Rear dust shield ===
=== Rear disk brake rotor ===
Note that for vehicles with M113 V8 engine (S500/S430) the rear caliper is around 1cm wider than on vehicles with M112 V6 engine (S350), therefore the rear disk rotor for M113 V8 engine is 22mm thick, while for M112 V6 engine only 11m.
{|
|
S500/S430:
* OE A2204230212 (120 EUR)
* TRW DF4437 (42 EUR/piece)
 
[[File:W220_rear_disk_rotors_TRW_DF4437.jpg|thumb|none|TRW DF4437 brake disk (22mm thick)]]
|
S350:
* OE A2204230112 (114 EUR)
* TRW DF4436 (36 EUR/piece)
 
[[File:W220_rear_disk_rotors_TRW_DF4436.jpg|thumb|none|TRW DF4436 brake disk (11mm thick)]]
|}
 
=== Rear disk brake pads ===
Brake pads are sold in pairs (for both sides).
* OE A0034205120 (87 EUR)
* TRW GDB1546DTE (35 EUR)
 
[[File:W220_Rear_brake_pads_Trw_GDB1546DTE.jpg|thumb|none|TRW GDB1546DTE brake pads]]
 
=== Brake shoes ===
For installation instructions see [[parking brake]] page.
 
Part numbers (set for both sides):
* OE - A2204200520 (87 EUR)
* Ate 03.0137-4016.2 (35 EUR) - comes with springs
* TRW GS8482 (30 EUR)
 
[[File:W220_brake_shoes_Ate_03013740162.jpg|thumb|none|Brake shoes (Ate 03.0137-4016.2)]]
 
==== Brake shoe extension springs ====
Part numbers (number of pieces for both sides):
* Extension spring, brake shoe pull-back (x2) - A2104230092, FEBI BILSTEIN 02105 (0.23 EUR)
* Extension spring, brake shoe pull-back (x2) - A2014230692 (replaced by A1714230092), FEBI BILSTEIN 02104 (0.71 EUR)
* Extension spring, brake shoes to cover plates (x4) - A2014230592, FEBI BILSTEIN 02103 (0.24 EUR)
 
{|
|[[File:W220_A2104230092_brake_shoe_pull-back.jpg|thumb|none|Brake shoe pull-back (A2104230092)]]
|[[File:W220_A2014230692_A1714230092_brake_shoe_pull-back.jpg|thumb|none|Brake shoe pull-back (A2014230692)]]
|[[File:W220_A2014230592_brake_shoes_to_cover_plates.jpg|thumb|none|Brake shoes to cover plates (A2014230592)]]
|}


[[File:W220_dust_shield_rear_left_A2204230420.jpg|thumb|none|Dust shield rear left (A2204230420)]]
==== Brake shoe expansion lock ====
Part numbers (set for both sides):
* OE - A2014200589 (13 EUR)
* ATE 03.0137-9704.2 (6 EUR)
{|
|[[File:W220_brake_shoe_expanshion_lock_Ate_03013797042.jpg|thumb|none|Brake shoe expansion lock (ATE 03.0137-9704.2)]]
|[[File:W220_brake_shoe_expansion_lock_ATE_03.0137-9704.2.jpg|thumb|none|Brake shoe expansion lock (ATE 03.0137-9704.2)]]
|[[File:W220_new_brake_shoe_expansion_lock_mounted.jpg|thumb|none|Brake shoe expansion lock mounted]]
|}


=== Rear dust shield ===
{|
|
Part numbers (left):
Part numbers (left):
* OE left: A2204230420 (124 EUR)
* OE left: A2204230420 (96 EUR)
* A.b.s. 11320 (30 EUR)
* A.b.s. 11320 (30 EUR)
* METZGER 6115177 (20 EUR)
* METZGER 6115177 (20 EUR)
 
* Triscan 812523214 (23 EUR)
* Nk 233342 (26 EUR)
|
Part numbers (right):
Part numbers (right):
* OE right: A2204230520 (124 EUR)
* OE right: A2204230520 (125 EUR)
* A.b.s. 11321 (30 EUR)
* A.b.s. 11321 (30 EUR)
* METZGER 6115178 (20 EUR)
* METZGER 6115178 (20 EUR)
* Triscan 812523215 (23 EUR)
|}
{|
|[[File:W220_dust_shield_rear_left_A2204230420.jpg|thumb|none|Dust shield rear left (A2204230420)]]
|[[File:W220_rear_dust_shields_Metzger.jpg|thumb|none|Rear durst shields left and right (METZGER)]]
|}
The dust shield is attached to the wheel carrier using two E10 (A2204230071) and two 13mm (A2204230371) bots.
{|
|[[File:W220_A2204230071_dust_shield_bolt_E10.jpg|thumb|none|Bolt E10 M6x12 (A2204230071)]]
|[[File:W220_A2204230371_dust_shield_bolt_13mm.jpg|thumb|none|Bolt 13mm M8x12 (A2204230371)]]
|}
Removal of two E10 bolts may be challenging if the heads for the bolts are rusted. Access through the wheel hub is angled, hence it may be required to hammer on E10 socket to get grip. The original E10 bolts can be replaced with standard M6x12 bolts. To mount a new dust shield without removing wheel bearing (overly complex job), the dust shield has to be cut in two places and pushed over wheel hub (see below). The cut can be welded or glued using, e.g., Kafuter A+B glue. The cut will not be visible as it will be covered by brake caliper.
{|
|[[File:W220_rear_dust_shield_E10_bolt_removal.jpg|thumb|none|Removal of rear dust shield E10 bolt]]
|[[File:W220_mounting_rear_right_dust_shield_cut.jpg|thumb|none|Mounting cut rear right dust shield]]
|[[File:W220_rear_right_dust_shield_welded_glued.jpg|thumb|none|Rear right dust shield glued back together]]
|[[File:W220_new_rear_dust_shield_with_brake_shoes_mounted.jpg|thumb|none|Rear right dust shield with brake shoes mounted]]
|}
=== Rear axle wiring ===
[[File:W220_rear_axle_wiring.png|thumb|none|Rear axle wiring]]
The rear brake pad wear sensor is the same part as for the front. The sensor attaches to the rear right inner brake pad.
[[File:W220_brake_pad_wear_sensor_A2205400717.jpg|thumb|none|Brake pad wear sensor (A2205400717)]]
The wear sensor wiring bracket (A2205460843) is attached to the rear right dust shield.
[[File:W220_A2205460843_rear_right_wear_indicator_bracket.jpg|thumb|none|Rear right wear indicator wiring bracket (A2205460843)]]
The rear wear indicator wire is attached to the right caliper using E10 torx bolt (N91014300600).
[[File:W220_N910143006002_brake_wear_indicator_bolt.jpg|thumb|none|Rear right wear indicator bolt M6x20 (N91014300600)]]
==== Speed sensor ====
The OE sensors are manufactured by BOSCH.
* Speed sensor rear left - A2205400417 / BOSCH 0265007008
* Speed sensor rear right - A2205400517 / BOSCH 0265007006
{|
|[[File:W220_rear_right_speed_sensor_A2205400517.jpg|thumb|none|Rear right speed sensor (A2205400517)]]
|[[File:W220_speed_sensor_rear_right_installed.jpg|thumb|none|Rear right speed sensor installed]]
|}
=== Rear brake caliper ===
==== Repair kit ([[facelift]]) ====
Guide sleeve kit:
* OE A0004200776 (20 EUR)
* ATE 11010142022 (8 EUR)
{|
|[[File:W220_rear_brake_caliper_guide_sleeve_kit_A0004200776.jpg|thumb|none|Guide sleeve kit A0004200776]]
|[[File:W220_rear_brake_caliper_guide_sleeve_kit_ATE_11.0101-4202.2.jpg|thumb|none|Guide sleeve kit ATE 11.0101-4202.2]]
|}
Guide bolt:
* OE A0004211018 (18 EUR)
* OEM ATE 11817100721 (8 EUR)
{|
|[[File:W220_rear_brake_caliper_guide_bolt_A0004211018.jpg|thumb|none|Guide bolt A0004211018]]
|[[File:W220_rear_brake_caliper_guide_bolt_ATE_11.8171-0072.1.jpg|thumb|none|Guide bolt ATE 11.8171-0072.1]]
|}
'''Please note that in ATE brake systems with open caliper guides the guides must not be lubricated!'''
Gasket set:
* OE A0004219986 (25 EUR)
* OEM ATE 11044142032 (10 EUR)
{|
|[[File:W220_rear_brake_caliper_gasket_set_A0004219986.jpg|thumb|none|Gasket set A0004219986]]
|[[File:W220_rear_brake_caliper_gasket_set_ATE_11.0441-4203.2.jpg|thumb|none|Gasket set ATE 11.0441-4203.2]]
|}
Retaining spring:
* OE A0004218591 (12 EUR)
* OEM ATE 11811603231 (5 EUR)
{|
|[[File:W220_rear_brake_caliper_retaining_spring_A0004218591.jpg|thumb|none|Retaining spring A0004218591]]
|[[File:W220_rear_brake_caliper_retaining_spring_ATE_11.8116-0323.1.jpg|thumb|none|Retaining spring ATE 11.8116-0323.1]]
|}
Brake cylinder paste:
* ATE 03990205102 (7 EUR)
The ATE brake cylinder paste ensures the necessary lubrication and preservation of hydraulic brake components and clutch parts. It is applied thinly and evenly to the cylinder surfaces, piston and sealing elements. - ATE brake cylinder paste is compatible with DOT 3, DOT 4 and DOT 5.1 brake fluids. - Easy installation of hydraulic brake parts - protects the treads from corrosion.
[[File:W220_brake_cylinder_paste_ATE_03.9902-0510.2.jpg|thumb|none|ATE brake cylinder paste 03.9902-0510.2]]


=== Rear brake pads replacement ===
=== Rear brake pads replacement ===
Line 134: Line 316:
* Locking bolt of rear/front axle brake disk: Nm 10
* Locking bolt of rear/front axle brake disk: Nm 10
* Bolt, brake cable at parking brake cable slack adjuster 12
* Bolt, brake cable at parking brake cable slack adjuster 12
== Brake lines ==
[[File:W220_copper_brake_line_4.75mm_connectors.jpg|thumb|none|Part of the original brake line replaced with copper brake line and 4.75mm connectors]]


== Brake fluid replacement ==
== Brake fluid replacement ==


Regular Flush Every Two Years. Brake fluid DOT4 is hydroscopic (absorbs water) and needs to be exchanged every two years under the maintenance schedule. A local dealer quoted $95 for this task. Plan for between 1-1.5 hrs if you DIY.
Flush brake fluid regularly - every two years. Brake fluid DOT4 is hydroscopic (absorbs water) and needs to be exchanged every two years under the maintenance schedule. A local dealer quoted $95 for this task. Plan for between 1-1.5 hrs if you DIY.


'''Warnings'''
'''Warnings'''
* It is critically important to use the DOT rating specified in the owner’s manual.
* It is critically important to use the DOT rating specified in the owner's manual (DOT4).
* Brake fluid is hazardous. Wear latex gloves, safety glasses, and protect the paint of your car.
* Brake fluid is hazardous. Wear latex gloves, safety glasses, and protect the paint of your car.
 
* CAUTION: DO NOT SPRAY THE FLUID, otherwise you will be getting a new paint job.
'''DIY Brake Fluid Flush'''
* Suck out old fluid in reservoir using a miti-vac or a turkey baster.
* Top off with NEW UNOPENED DOT-4 PLUS fluid ONLY!  
* Top off with NEW UNOPENED DOT-4 PLUS fluid ONLY!  
* Connect Power Bleeder which has been filled with NEW UNOPENED DOT-4 PLUS fluid!
* Bleed all four calipers one by one in the following sequence: rear right, rear left, front right, front left.
* Pressurize the brake system with the Power Bleeder (138KPa (20 psi) via the integrated pump).
* Check the fluid level in reservoar after every 20 brake pedal presses.
* Bleed all four callipers, LR, RR, LF and then RF.
* Inspect for leaks.
* Inspect for leaks.
* Depressurize the system, CAUTION: DO NOT SPRAY THE FLUID, otherwise you will be getting a new paint job.
* Record brake flush in maintenance records.
* Do a manual check of brake pressure
* Dispose of old brake fluid responsibly.
* Make a final check of the level of fluid in the brake reservoir.
 
* Record Brake Flush in Maintenance Records.
Tools needed:
* Dispose of old brake fluid responsibly .
* Transparent pipe with 6mm inner diamater ~75cm long.
* 11mm wrench for unscrewing bleeding screw at brake caliper.
 
Torque specification:
* Bleed screw to brake caliper: 7 Nm
 
TIP: If possible alternate brake fluid colour from one flush to the next.
The difference in colour gives good confidence that everything is flushed out.
 
<!-- AR42.10-P-0010I, Bleed brake system, 10.11.11
MODEL 215, 220 -->


TIP: If possible alternate brake fluid colour from one flush to the next.  The difference in colour gives good confidence that everything is flushed out.
Brake fluid filling capacity on model 220 and 215 is 0.7 to 0.9 liters. Quantity of brake fluid required for a thorough flush will be about 3L in practice.


Quantity of Brake Fluid Required for a Thorough Flush: It will use about 3L for a full and thorough flush.
{|
|[[File:W220_brake_fluid_flushing_setup.jpg|thumb|none|Simple one-man brake fluid flush setup]]
|[[File:W220_sequence_for_bleeding_brake_fluid.png|thumb|none|Sequence of bleeding operation for brake calipers with one bleed screw]]
|[[File:W220_sequence_for_bleeding_brake_fluid_8piston_calipers.png|thumb|none|Sequence of bleeding operation for 8-piston brake calipers at front axle with two bleed screws. Observe different sequence of bleeding operation for left-hand and right-hand drive vehicles.]]
|}


The following video shows how to completely flush and replace the Brake Fluid using the Pressure Vacuum method.
The following video shows how to completely flush and replace the brake fluid using a simple bottle method vs the pressure vacuum method.
{|
{|
|{{#ev:youtube|https://youtu.be/GfosobLjGQE|320|center|W220 Brake Fluid Flush (By Masood)|frame}}
|{{#ev:youtube|https://www.youtube.com/watch?v=TOF4vhblUvw|320|center|Simple brake fluid flush setup|frame}}
|{{#ev:youtube|https://www.youtube.com/watch?v=GfosobLjGQE|320|center|Brake fluid flush using the pressure vacuum method|frame}}
|}
|}


Line 175: Line 373:
|[[File:DOT4_1L_Febi_bilstein_23930.jpg|thumb|none|FEBI BILSTEIN 23930 (1l)]]
|[[File:DOT4_1L_Febi_bilstein_23930.jpg|thumb|none|FEBI BILSTEIN 23930 (1l)]]
|[[File:DOT4_5L_Febi_bilstein_23932.jpg|thumb|none|FEBI BILSTEIN 23932 (5l)]]
|[[File:DOT4_5L_Febi_bilstein_23932.jpg|thumb|none|FEBI BILSTEIN 23932 (5l)]]
|}
== Brake Light Switch ==
If you are getting the ABS and ESP lights with a VISIT WORKSHOP warning and the BAS ESP light, then look no further.  Chances are your brake light switch needs to be replaced.  This video is shot on an E320, but many Mercedes cars including SL500, SL55 AMG, SL600, CL500, CL55 AMG, CL600, S500 S430, CL65 AMG SL65 AMG, S350, S65 AMG, S55 AMG, SL550, SL63 AMG and S600 use the same Brake Light Switch and setup.
{|
|{{#ev:youtube|https://youtu.be/jKoS5-Lsl3A|320|center|W210/W220 Brake Light Switch or Brake Stop Sensor Switch Replacement (By Masood)|frame}}
|}
|}

Latest revision as of 16:48, 16 September 2023

Front brakes

Front brake-related parts in EPC

Front disk brake rotor

Front brake disks on vehicles with M113 engines (S430/S500) are larger and thicker compared to vehicles with M112 engines (S280/S320/S500).

S500/S430:

  • OE A2204212512 (135 EUR)
  • ATE 24.0132-0115.1 (75 EUR/piece)
  • TRW DF4148S (58 EUR/piece)
TRW DF4148S brake disk (32mm thick, 330mm diameter)

S280/S320/S350:

  • OE A2204210912 (135 EUR)
  • ATE 24.0128-0125.1 (69 EUR/piece)
  • TRW DF4149S (56 EUR/piece)
TRW DF4149S brake disk (28mm thick, 312mm diameter)

Front disk brake pads

Brake pads are sold in pairs (for both sides).

  • OE A0044209020 (112 EUR)
  • ATE 13.0470-4990.2 (67 EUR)
  • TRW GDB1543DTE (50 EUR)
TRW GDB1543DTE brake pads

Accessory kit

In case brake pads are changed after several years, the spring bolts become seized and to remove them they have to be bent and broken out (see photo below). When buying brake accessory kit, make sure to purchase spring that has bolt anchors (e.g., kit by ATE) to prevent spring from slipping off the bolts (see photos below).

Removing seized spring bolts
Brake spring slipped off the bolts
Brake spring with bolt anchors

Part numbers:

  • Spring - A0004217891 (replaced by A0004219791) (14 EUR)
  • Bolts - A0019915160 (12 EUR)
  • Kit - ATE 13.0460-0237.2 (9 EUR)
ATE 13.0460-0237.2 accessory kit
ATE 13.0460-0237.2 accessory kit

Front dust shield

It is common for the dust shield (also known as a protective plate) to rust in the bolt holes resulting in the dust shield touching disk rotor. The original dust shields are quote expensive, unfortunately, aftermarket dust shields for the front axle are not available in the market.

Rusted bolt holes fixed by installing large washers

Part numbers:

  • OE left: A2204200444 (124 EUR)
  • OE right: A2204200544 (88 EUR)
Dust shield front left (A2204200444)

Remove/install brake disc (front axle)

  • 61 - Brake disk
  • 63 - Security bolt

Remove/install:

  1. Remove wheels
  2. Check brake lining thickness and brake disks (61). Inspect condition of brake disks. Check brake lining thickness. Only replace brake pads and brake disks (61) in complete sets if necessary. If the brake pads have worn down to beyond the wear limit, the bar between the sealing groove and dust cap may be damaged; therefore: Inspect brake system for leaks with pressure tester.
  3. Remove brake disk. Do not detach brake hose, instead attach brake caliper to vehicle so that it is free of tension. Do not kink or tension brake hose, as otherwise it will be damaged.
  4. Remove locking bolt (64) and remove brake disk (61). Installation: Replace securing bolt (64)

Clean:

  1. Clean contact surfaces and seat of brake disk (61) if necessary.
  2. Lightly grease seat of brake disk (61) using Hot lubricating paste.
  3. Install in the reverse order

Checking:

  1. Carry out brake test on the test stand

Torque specifications:

  • Locking bolt of rear/front axle brake disk: Nm 10
Load video
YouTube
W220 Front Brake Rotors Replacement (By Masood)

Rear brakes

Rear brake-related parts in EPC

Rear disk brake rotor

Note that for vehicles with M113 V8 engine (S500/S430) the rear caliper is around 1cm wider than on vehicles with M112 V6 engine (S350), therefore the rear disk rotor for M113 V8 engine is 22mm thick, while for M112 V6 engine only 11m.

S500/S430:

  • OE A2204230212 (120 EUR)
  • TRW DF4437 (42 EUR/piece)
TRW DF4437 brake disk (22mm thick)

S350:

  • OE A2204230112 (114 EUR)
  • TRW DF4436 (36 EUR/piece)
TRW DF4436 brake disk (11mm thick)

Rear disk brake pads

Brake pads are sold in pairs (for both sides).

  • OE A0034205120 (87 EUR)
  • TRW GDB1546DTE (35 EUR)
TRW GDB1546DTE brake pads

Brake shoes

For installation instructions see parking brake page.

Part numbers (set for both sides):

  • OE - A2204200520 (87 EUR)
  • Ate 03.0137-4016.2 (35 EUR) - comes with springs
  • TRW GS8482 (30 EUR)
Brake shoes (Ate 03.0137-4016.2)

Brake shoe extension springs

Part numbers (number of pieces for both sides):

  • Extension spring, brake shoe pull-back (x2) - A2104230092, FEBI BILSTEIN 02105 (0.23 EUR)
  • Extension spring, brake shoe pull-back (x2) - A2014230692 (replaced by A1714230092), FEBI BILSTEIN 02104 (0.71 EUR)
  • Extension spring, brake shoes to cover plates (x4) - A2014230592, FEBI BILSTEIN 02103 (0.24 EUR)
Brake shoe pull-back (A2104230092)
Brake shoe pull-back (A2014230692)
Brake shoes to cover plates (A2014230592)

Brake shoe expansion lock

Part numbers (set for both sides):

  • OE - A2014200589 (13 EUR)
  • ATE 03.0137-9704.2 (6 EUR)
Brake shoe expansion lock (ATE 03.0137-9704.2)
Brake shoe expansion lock (ATE 03.0137-9704.2)
Brake shoe expansion lock mounted

Rear dust shield

Part numbers (left):

  • OE left: A2204230420 (96 EUR)
  • A.b.s. 11320 (30 EUR)
  • METZGER 6115177 (20 EUR)
  • Triscan 812523214 (23 EUR)
  • Nk 233342 (26 EUR)

Part numbers (right):

  • OE right: A2204230520 (125 EUR)
  • A.b.s. 11321 (30 EUR)
  • METZGER 6115178 (20 EUR)
  • Triscan 812523215 (23 EUR)
Dust shield rear left (A2204230420)
Rear durst shields left and right (METZGER)

The dust shield is attached to the wheel carrier using two E10 (A2204230071) and two 13mm (A2204230371) bots.

Bolt E10 M6x12 (A2204230071)
Bolt 13mm M8x12 (A2204230371)

Removal of two E10 bolts may be challenging if the heads for the bolts are rusted. Access through the wheel hub is angled, hence it may be required to hammer on E10 socket to get grip. The original E10 bolts can be replaced with standard M6x12 bolts. To mount a new dust shield without removing wheel bearing (overly complex job), the dust shield has to be cut in two places and pushed over wheel hub (see below). The cut can be welded or glued using, e.g., Kafuter A+B glue. The cut will not be visible as it will be covered by brake caliper.

Removal of rear dust shield E10 bolt
Mounting cut rear right dust shield
Rear right dust shield glued back together
Rear right dust shield with brake shoes mounted

Rear axle wiring

Rear axle wiring

The rear brake pad wear sensor is the same part as for the front. The sensor attaches to the rear right inner brake pad.

Brake pad wear sensor (A2205400717)

The wear sensor wiring bracket (A2205460843) is attached to the rear right dust shield.

Rear right wear indicator wiring bracket (A2205460843)

The rear wear indicator wire is attached to the right caliper using E10 torx bolt (N91014300600).

Rear right wear indicator bolt M6x20 (N91014300600)

Speed sensor

The OE sensors are manufactured by BOSCH.

  • Speed sensor rear left - A2205400417 / BOSCH 0265007008
  • Speed sensor rear right - A2205400517 / BOSCH 0265007006
Rear right speed sensor (A2205400517)
Rear right speed sensor installed

Rear brake caliper

Repair kit (facelift)

Guide sleeve kit:

  • OE A0004200776 (20 EUR)
  • ATE 11010142022 (8 EUR)
Guide sleeve kit A0004200776
Guide sleeve kit ATE 11.0101-4202.2

Guide bolt:

  • OE A0004211018 (18 EUR)
  • OEM ATE 11817100721 (8 EUR)
Guide bolt A0004211018
Guide bolt ATE 11.8171-0072.1

Please note that in ATE brake systems with open caliper guides the guides must not be lubricated!

Gasket set:

  • OE A0004219986 (25 EUR)
  • OEM ATE 11044142032 (10 EUR)
Gasket set A0004219986
Gasket set ATE 11.0441-4203.2

Retaining spring:

  • OE A0004218591 (12 EUR)
  • OEM ATE 11811603231 (5 EUR)
Retaining spring A0004218591
Retaining spring ATE 11.8116-0323.1

Brake cylinder paste:

  • ATE 03990205102 (7 EUR)

The ATE brake cylinder paste ensures the necessary lubrication and preservation of hydraulic brake components and clutch parts. It is applied thinly and evenly to the cylinder surfaces, piston and sealing elements. - ATE brake cylinder paste is compatible with DOT 3, DOT 4 and DOT 5.1 brake fluids. - Easy installation of hydraulic brake parts - protects the treads from corrosion.

ATE brake cylinder paste 03.9902-0510.2

Rear brake pads replacement

This video shows how to replace front and rear brake pads. The video shows part numbers for the Brake Pads (Front and Rear) and Pad Wear Sensor. Torque values are also shown.

Load video
YouTube
W220 Brake Pads Replacement (By Masood)

Rear driver brake caliper replacement

This video shows how to replace the rear driver caliper in a left steered car. The procedure is very similar for the other wheels.

Load video
YouTube
W220 Rear Brake Caliper Replacement (By Masood)

Remove/install brake disc (rear axle)

  • 61 - Brake disk
  • 63 - Security bolt

Remove/install:

  1. Remove wheels
  2. Release parking brake
  3. Check brake lining thickness and brake disks (61). Inspect condition of brake disks. Check brake lining thickness. Only replace brake pads and brake disks (61) in complete sets if necessary. If the brake pads have worn down to beyond the wear limit, the bar between the sealing groove and dust cap may be damaged; therefore: Inspect brake system for leaks with pressure tester.
  4. Remove brake disk. Do not detach brake hose, instead attach brake caliper to vehicle so that it is free of tension. Do not kink or tension brake hose, as otherwise it will be damaged.
  5. Preloading automatic cable slack adjuster
  6. Remove locking bolt (64) and remove brake disk (61). If parking brake drums are run in, turn back the adjusting mechanism of the parking brake beforehand. Otherwise the brake shoes will be damaged. See: Adjusting parking brake. Installation: Replace securing bolt (64)

Clean:

  1. Clean contact surfaces and seat of brake disk (61) if necessary.
  2. Lightly grease seat of brake disk (61) using Hot lubricating paste.
  3. Check condition of brake shoes of parking brake. If necessary: replace parking brake brake shoes:
  4. Install in the reverse order

Checking:

  1. Check version of pedal assembly
  2. Adjust parking brake
  3. Release automatic slack adjuster
  4. Carry out brake test on the test stand

Torque specifications:

  • Locking bolt of rear/front axle brake disk: Nm 10
  • Bolt, brake cable at parking brake cable slack adjuster 12

Brake lines

Part of the original brake line replaced with copper brake line and 4.75mm connectors

Brake fluid replacement

Flush brake fluid regularly - every two years. Brake fluid DOT4 is hydroscopic (absorbs water) and needs to be exchanged every two years under the maintenance schedule. A local dealer quoted $95 for this task. Plan for between 1-1.5 hrs if you DIY.

Warnings

  • It is critically important to use the DOT rating specified in the owner's manual (DOT4).
  • Brake fluid is hazardous. Wear latex gloves, safety glasses, and protect the paint of your car.
  • CAUTION: DO NOT SPRAY THE FLUID, otherwise you will be getting a new paint job.
  • Top off with NEW UNOPENED DOT-4 PLUS fluid ONLY!
  • Bleed all four calipers one by one in the following sequence: rear right, rear left, front right, front left.
  • Check the fluid level in reservoar after every 20 brake pedal presses.
  • Inspect for leaks.
  • Record brake flush in maintenance records.
  • Dispose of old brake fluid responsibly.

Tools needed:

  • Transparent pipe with 6mm inner diamater ~75cm long.
  • 11mm wrench for unscrewing bleeding screw at brake caliper.

Torque specification:

  • Bleed screw to brake caliper: 7 Nm

TIP: If possible alternate brake fluid colour from one flush to the next. The difference in colour gives good confidence that everything is flushed out.


Brake fluid filling capacity on model 220 and 215 is 0.7 to 0.9 liters. Quantity of brake fluid required for a thorough flush will be about 3L in practice.

Simple one-man brake fluid flush setup
Sequence of bleeding operation for brake calipers with one bleed screw
Sequence of bleeding operation for 8-piston brake calipers at front axle with two bleed screws. Observe different sequence of bleeding operation for left-hand and right-hand drive vehicles.

The following video shows how to completely flush and replace the brake fluid using a simple bottle method vs the pressure vacuum method.

Load video
YouTube
Simple brake fluid flush setup
Load video
YouTube
Brake fluid flush using the pressure vacuum method

Parts

DOT 4 brake oils (MB 331.0 spec):

  • FEBI BILSTEIN 26748 (0.25l) - 2.5 EUR
  • FEBI BILSTEIN 23930 (1l) - 7.4 EUR
  • FEBI BILSTEIN 23932 (5l) - 26.4 EUR
FEBI BILSTEIN 26748 (0.25l)
FEBI BILSTEIN 23930 (1l)
FEBI BILSTEIN 23932 (5l)

Brake Light Switch

If you are getting the ABS and ESP lights with a VISIT WORKSHOP warning and the BAS ESP light, then look no further. Chances are your brake light switch needs to be replaced. This video is shot on an E320, but many Mercedes cars including SL500, SL55 AMG, SL600, CL500, CL55 AMG, CL600, S500 S430, CL65 AMG SL65 AMG, S350, S65 AMG, S55 AMG, SL550, SL63 AMG and S600 use the same Brake Light Switch and setup.

Load video
YouTube
W210/W220 Brake Light Switch or Brake Stop Sensor Switch Replacement (By Masood)
Retrieved from "https://w220.wiki/index.php?title=Brakes&oldid=8989"