Exhaust system: Difference between revisions

Revision as of 02:50, 14 March 2019

Occasionally the exhaust system will develop an annoying but quiet rattle. This may be a simple loose bracket, heat shield or clamp.
Occasionally the exhaust system will develop an intermittent but very loud rattle. W220's are known to have an issue with the catalytic converters which come apart internally and make a loud rattling sound at particular engine speeds (around 2,500 RPM) and temperatures (sometimes only when the cat is hot). It is often first noticed when driving around a multi-level parking station where the sound bounces off the close solid walls. M-B issued an eight year / 80,000 mile (125,000 Km) warranty to cover the failed catalytic converters. Some owners have found that it is mostly the rear cats that fail. Video shows a ML55 but is a good example of a noisy catalytic converter at idle speed.

Catalytic converters must not be disposed of as regular scrap. The catalytic converter contains valuable rare earth metals, which can be recycled.

Beware that often the rear cat will rattle because it is full of substrate that has broken down in the front cat and simply ended up in the rear cat.
If replacing the catalytic converters with after market ones, go with a metal substrate catalytic converter since it will flow much better than a ceramic one.
When reassembling a new or repaired exhaust system apply high temperature anti-seize copper grease to all the gaskets, seal rings, flange surfaces, and bolt threads. You will really appreciate having done this next time the system has to come apart.
Also cover all exposed bolt threads with silicon to prevent corrosion. The silicon is easily peeled off before undoing the next time. If you have previously used the copper anti-seize grease you will be able to undo the nut by hand.

210 Seal Ring Catalyst on Flange Right 1269970041 and 2024920181
220 Seal Ring Catalyst on Flange Left 140920281 and 202490281
245 Seal Ring Left to Right Pipe to Exhaust Pipe 2024920281 ie same as 220 Seal Ring Catalyst on Flange Left
OEM catalytic converters cost around $1,200 but cheap aftermarket cats are available for under $300 installed.

To investigate an annoying rattle jack the vehicle up and place on stands. (TIP: You may find that When you put the car up on front jack stands only, it will not rattle. One BenzWorld enthusiast Had to level out the back of the car to get the rattle going.)

Tap the complete exhaust system with a rubber mallet while listening for the rattle. If you are lucky it is often a broken strap or bracket making the noise. If you are unlucky you may have the dreaded interval issue with the catalytic converters.

One enthusiast discovered it was a slight rattle coming from a rear cat. He took a hammer and put a little dent in the bottom of the cat to keep the internals from moving around and making noise. He reported after one year that the cats were still rattle free. (TIP: Be warned that any warranty will be void if there are dents found on the cats from someone trying to hold in the honeycomb substrate. Not a problem if you exceed the warranty period, but a caution for others with a newer vintage / class of car.)

@@ Line 12: / Line 12: @@
 ==Tips - Exhaust Pipes, Catalytic Converter, Mufflers==
-* Beware that often the rear cat will rattle because it is full of substrate that had broken down in the front cat and simply ended up in the rear cat.
+* Beware that often the rear cat will rattle because it is full of substrate that has broken down in the front cat and simply ended up in the rear cat.
+* If replacing the catalytic converters with after market ones, go with a metal substrate catalytic converter since it will flow much better than a ceramic one.
 * When reassembling a new or repaired exhaust system apply high temperature anti-seize copper grease to all the gaskets, seal rings, flange surfaces, and bolt threads. You will really appreciate having done this next time the system has to come apart.
 * Also cover all exposed bolt threads with silicon to prevent corrosion. The silicon is easily peeled off before undoing the next time. If you have previously used the copper anti-seize grease you will be able to undo the nut by hand.