Windshield

Windshield

W220 vehicles have windshield

Infrared Reflecting Windshield

Vehicles with option code HEAT INSULATING+IR REFLECTG.SAFETY GLASS ALL-ROUND are equipped with infrared reflecting glass including windshield, which reduces the amount of radiated heat entering the interior through the windows.

"IR" mark on the windshield denoting infrared reflecting glass.

Infrared transparent areas

The infrared reflecting glass also prevents the transmission of signals through the glass by in-vehicle electronic devices (e.g. electronic toll collection devices). To allow the use of these devices in the vehicle, two infrared transparent areas (1) and (2) are placed in the windshield.

(1) Mounting location for electronic toll collection devices (infrared transparent) (2) Infrared transparent area (pass-through for electronic signals) (3) 31.5 in (80 cm) (4) 19.0 in (48 cm) (5) 1.75 in (4.5 cm)

Installing Windshield

1 - Windshield 2 - Heated window connector

Remove

1. Remove rain sensor (B38)
2. Unclip automatic light switch daylight sensor (B32/1)
3. Remove wiper arms. Always remove ignition key when working on windshield wiper mechanism.
4. Remove water deflector over wiper system
5. Disconnect electrical connector for heated window (2)
6. Remove both panelings from outside of A-pillar
7. Remove ornamental frame on windshield.
8. Cut out windshield (1) with Roll Out 2004 window removal tool
9. Remove windshield (1) from body with Cup suction tools

Install

1. Prepare 1-component adhesive cartridge 000589866300
2. Prepare body flange for installation of window
3. Replace rubber spacers. Do not remove protective foil.
4. Prepare windshield (1) for glazing.
5. Align windshield (1) in the body opening. Observe gap - distance between top edge of window and front edge of roof. Dimension "A" mm 12.
6. Remove protective foil from rubber spacers.
7. Smooth sealing channel with hand roller.
8. Apply adhesive material. Install windshield (1) within 10 minutes before adhesive force of adhesive material starts to decrease. Height of glue bead approx. 13 mm.
9. Install windshield (1). Open a side window in the vehicle to prevent the windshield (1) from being pressed outward by air pressure when the door is closed.
10. The waiting time (time before vehicle can be driven) is approx. 1 h calculated from the time the windshield (1) is installed.
11. Install ornamental frame on wind deflector.
12. Install paneling on outside of A-pillar.
13. Install water repellent over wiper system.
14. Install wiper arms.
15. Disconnect electric connector (2) for heated window.
16. Install rain sensor.
17. Clip in automatic light switch daylight sensor.
18. Clean windshield (1).
19. Code adaptation of rain sensor and light sensor amplification factor and select type of windshield. Engine hood and driver door must be closed. Connect STAR DIAGNOSIS and read out fault memory.

Rain Sensor

In facelift vehicles there is no separate daylight sensor, since daylight sensor is integrated in the rain sensor.

Part No.	Notes
A2108205710	To Date: 30/09/2002
A2098200726	From Date: 30/09/2002, Replaced by: A2098202426
A2098202426	From Date: 30/09/2002, Replaced by: A2098203126
A2098203126	From Date: 30/09/2002, Replaced by: A2218702826
A2218702826	From Date: 30/09/2002

A2108205710 - pre-facelift rain sensor (back).

A2108205710 - pre-facelift rain sensor (front).

A2108205710 - pre-facelift rain sensor (side).

A2218702826 - facelift rain and daylight sensor (back).

A2218702826 - facelift rain and daylight sensor (front).

A2218702826 - facelift rain and daylight sensor (side).

1 - Electrical connector 2 - Retaining clips 3 - Lens A67 - Inside rearview mirror unit B38 - Rain sensor

Remove/Install

1. Disconnect ground cable of battery
2. Remove inside rearview mirror unit (A67) with cover
3. Detach electrical connector (1) at rain sensor (B38)
4. Release retaining clamps (2) on rain sensor (B38) to left and right
5. Remove rain sensor (B38). The lens (3) of the rain sensor (B38) is bonded to the windshield and must not be removed, otherwise the lens (3) will be damaged.
6. Install in the reverse order.
7. Perform function check
8. Read coding of the windshield adaptation for rain sensor and of adaptation of the light sensor booster factor using STAR DIAGNOSIS and replace if necessary, select windshield variant.
9. Connect STAR DIAGNOSIS, read out fault memory

Daylight Sensor

In facelift vehicles there is no separate daylight sensor, since daylight sensor is integrated in rain sensor. For pre-facelift vehicles daylight sensor has part no. A2208203326.

A2208203326 - pre-facelift daylight sensor (back).

A2208203326 - pre-facelift daylight sensor (front).

1 - Cover 2 - Cover 3 - Plug-in wiring plug connection 4 - Clips B32/1 - Automatic light switch daylight sensor

Remove/Install

1. Disconnect ground cable of battery
2. Remove overhead control panel control unit
3. Unclip covering (1) and (2)
4. Release clips (4) on left and right
5. Remove automatic light switch daylight sensor (B32/1). Lens of automatic light switch daylight sensor (B32/1) is bonded to the windshield. Do not replace.
6. Unplug electrical connector (3) from automatic light switch daylight sensor (B32/1).
7. Install in the reverse order.
8. Perform function check.