Fuel tank

Fuel tank

W220 has fuel tank (A2204707601) with 88 liter (23 galon) volume, unless vehicle has option code 282 (SKI-BAG) or 308 (REFRIGERATOR IN REAR) in which case the fuel tank (A2204707701) has value of 78 liters (20 galons).

Fuel tank with attachment parts as in EPC.

Fuel tank (88l)

A2204707601 (top).

A2204707601 (bottom).

Fuel tank (78l)

A2204707701 (top).

A2204707701 (bottom).

Location/design/function

Shown without ski bag: 26 - Fuel strainer 26/1 - O-ring 75/4 - Cup seals 80 - Fuel tank 80/2 - Struts securing fuel tank 90/11 - Fuel return hose 90/12 - Fuel hose on the suction side with Connection D - Fuel tank-activated charcoal canister vent line (shown USA, otherwise with vent valve) E - Air admission line for diaphragm pressure regulator in fuel filter

The fuel tank (80) is located in the trunk above the rear axle. The fuel tank (80) is made of sheet steel.

The fuel is drawn through the fuel strainer (26) in the fuel inlet hose (90/12). The fuel flows back along the return flow hose (90/11). The vent line (D) runs to the activated charcoal canister (in some cases with vent valve).

Fuel reserve

The 88 liter tank uses 11 liters as a reserve. The 78 liter tank uses 10 liters as a reserve.

The reserve is what is left when the needle is pointed all the way down to the bottom of the yellow area and the fuel warning light comes on. Hence, the fuel gauge in the instrument cluster shows the fuel level minus the reserve volume.

Splash bowl

Shown on model 220: 42 - To fuel tank ventilation system 80 - Fuel tank 80/5 - Splash bowl 80/10 - Return flow line 80/11 - Fuel strainer 80/13 - Riser line 80/17 - Return flow nozzle 90/12 - Fuel suction hose 91 - Pressurization line 93 - Ventilation hose h - Fuel level

Shown on model 211: 1 - Left suction spray pump 2 - Bleed valve 3 - Pressure regulator valve 4 - Pressure regulator 5 - Right suction spray pump 6 - Splash bowl 7 - Fuel pump in swirl pot 80 - Fuel tank A - Return flow B - Feed line to engine h - Fuel level

The swirl pot is mounted in the fuel tank. The task of the splash bowl is supplying the engine with fuel in the event of a low fuel level in the fuel tank and during lengthy cornering.

The fuel return flow stream flows out of the return flow nozzle (80/17) into the splash bolw at a high velocity when the fuel pump is operated. As a result, the fuel around the return flow nozzle (80/17) is also entrained and carried into the splash bowl.

Fuel level sensor

89/1 - Lever-type sensor 89/2 - Potentiometer 89/3 - Sliding contacts B4 - Fuel level indicator sensor (except model 140)

The fuel level indicator sensor (also known as fuel gauge) is installed in the fuel tank via a bayonet latch.

The task of the sensor is determining the fuel level in the fuel tank. The fuel level sensor (B4) is a lever-type sensor with sliding contacts (potentiometer).

The resistance of the fuel gage sensor (B4) is analyzed in the electronics of the fuel gage. Example model 208: Low resistance = Fuel tank empty, High resistance = Fuel tank full. In the event of a open circuit the fuel gauge in the instrument cluster indicates empty. The fuel reserve warning lamp (A1e4) does not light up.

Fuel tank pressure sensor (USA)

Shown on model 210: B4 - Fuel gage sensor B4/3 - Fuel tank pressure sensor

The fuel tank pressure sensor is built into the hausing of the fuel gauge.

The task for the fuel tank pressure sensor is detecting the internal pressure of the fuel tank for the leak test of the fuel system.

The output signal depends on the pressure inside the tank and is transmitted to the engine control unit.

Remove/install fuel tank

Shown on fuel tank model 220: 26 - Fuel strainer 26/1 - O-ring 75/4 - Cup seals 76/1 - Vent line (diesel engine) 80 - Fuel tank 80/2 - Struts securing fuel tank 90/11 - Fuel return hose 90/12 - Fuel hose on the suction side with Connection fitting D - Fuel tank - activated charcoal canister line (gasoline engine) E - Fuel filter - fuel tank degassing line (gasoline engine)

Shown on fuel tank model 220 with option code 282 (SKI-BAG) or 308 (REFRIGERATOR IN REAR): 26 - Fuel strainer 26/1 - O-ring 75/4 - Cup seals 76/1 - Vent line (diesel engine) 80 - Fuel tank 80/1 - Rear wall of fuel tank 80/23 - Mounting rails 90/11 - Fuel return hose 90/12 - Fuel hose on the suction side with connection fitting D - Fuel tank - activated charcoal canister line (gasoline engine) E - Fuel filter - fuel tank degassing line (gasoline engine)

1. Drain fuel tank (80). Pay attention to fuel quantity.
2. Remove trim panel in trunk
3. With option code 282 (SKI-BAG) or 308 (REFRIGERATOR IN REAR): Remove rear wall of fuel tank (80/1)
4. With option code 282 (SKI-BAG) or 308 (REFRIGERATOR IN REAR): Detach lower mounting rails (80/23) of fuel tank rear wall (80/1) from trunk floor. Do not detach upper mounting rails (80/23) at rear shelf.
5. With option code 282 (SKI-BAG) or 308 (REFRIGERATOR IN REAR): Take spare tire out of spare tire well
6. Without option code 282 (SKI-BAG) or 308 (REFRIGERATOR IN REAR): Detach mounting struts (80/2) of fuel tank (80)
7. Raise vehicle
8. Vehicles with gasoline engine: Detach fuel hose on the suction side with connection fitting (90/12), fuel return hose (90/11), and fuel tank - activated charcoal canister line (gasoline engine). Do not damage fuel filter - fuel tank degassing line (gasoline engine) (E). Collect remaining fuel, seal connections.
9. Vehicles with diesel engine: Detach fuel hose on the suction side connection fitting (90/12), fuel return hose (90/11) and vent line (76/1). Collect remaining fuel, seal connections. Box wrench bit W000589710300.
10. Take out fuel tank (80). Inspect whether cup seals (75/4) can be re-used.
11. Check sound deadening mat for damage
12. Remove fuel strainer (26). Clean and check for re-usability. The splash bowl in the fuel tank is secured against turning with 2 pins. It is attached together with the fuel strainer (26).
13. Replace O-ring (26/1). Installation: Oil to facilitate installation.
14. Install in the reverse order

Torque specifications:

• Fuel strainer in fuel tank: 40 Nm
• Fuel hose with connection fitting on fuel strainer: 30 Nm

Box wrench bit W000589710300