Rear axle

Suspension

Air suspension struts are documented in Airmatic page.

Identifying the components in this diagram with same nomenclature as above:

Part	Part no.	Image	Description
185	A2203502606 (replaced by A2203502706) A2203502706 LEMFÖRDER 2509402 (33 EUR)		Thrust arm (left and right)
190	A2203503106 FEBI BILSTEIN 23459 (10 EUR)		Repair kit for thrust arm (left and right)
160	A2203500453		Tie rod / track control arm (left and right)
165	A2203520065		Rubber mount with eccentric interior bushing (left and right)
120	A2203502206		Torque strut / Radius rod (left and right)
80	A2203502406		Camber strut (left and right)
30	A2203521102		Spring control arm (left and right)
10	A2203520027 Lemförder 2099402 (20 EUR) TRW JBU167 (20 EUR)		Supporting joint (left and right)
42	A2209900604		Bolt. Spring control arm to wheel bearing (left and right) M14X1.5X80.
45	A1403521576		Washer. Spring control arm to wheel bearing (left and right).
50	N000000003281		Hexagon nut. Spring control arm to wheel bearing (left and right) M14X1,5.

Remove/install thrust arm

Shown on model 220 with Airmatic 5 - Thrust arm 5g - Thrust arm cover

1. Raise vehicle
2. Unclip thrust arm cover (5g).
3. Detach thrust arm (5) from wheel carrier and rear axle carrier. Installation: When tightening the camber strut the vehicle must be relieved of load and on its wheels. Otherwise the rubber mounts are constantly under preload and are damaged as a result.
4. Install in the reverse order

Torque specification:

• Self-locking nut, thrust arm to wheel carrier - Stage 1: 45 Nm, Stage 2: 45°

Special tool:

• Screw driver W119589001000 (12mm Triple Square XZN Socket)

12mm Triple Square XZN Socket (W119589001000 analog)

Load video YouTube YouTube might collect personal data. Privacy Policy ContinueDismiss Replacing rear right thrust arm

Remove/install supporting joint at wheel carrier (wheel carrier installed)

A failed rubber of supporting joint at wheel carrier is a common cause for a squeaking rear suspension.

Shown on model 220 with Airmatic 6 - Spring link 7 - Wheel carrier 7a - Support joint

1. Remove rear wheels
2. Remove spring link (6). In practice, it is sufficient to lower spring control arm by removing bolt to wheel carrier (21mm and E18) and removing stabilizer bar link bottom nut (16mm) and detach the bottom part of the stabilizer bar.
3. Remove supporting joint (7a) from wheel carrier (7)
4. Install in the reverse order

Remove/install supporting joint on wheel carrier

Remove supporting joint:

1. Pull supporting joint out of wheel carrier using the extraction and insertion tool.
2. Remove extraction and insertion tool with supporting joint.

Shown on model 220 with AIRMATIC 7a - Support joint 06a - Thrust piece part 01 06b - Counterholding bush part 02 06c - Clamping bolt 06d - Axial needle roller bearing

Install supporting joint:

1. Fit the extraction and insertion tool with supporting joint to wheel carrier.
2. Draw supporting joint into the wheel carrier from behind using the extraction and insertion tool.

Shown on model 220 with AIRMATIC Using the thrust piece part 01 (06a) draw in the supporting joint until it abuts the machined contact surface (arrow). The supporting joint has been properly inserted when it is in the center of the wheel carrier boss.

Special tool W202589004300

Supporting joint A2203520027

Supporting joint installed

Load video YouTube YouTube might collect personal data. Privacy Policy ContinueDismiss Squeaking joint at rear wheel carrier

Replace rubber mounts of rear shock absorbers

A quick temporary fix for a squeaking bushes is to make a slit in the rubber seal and inject some oil.

01 - Extraction and installation tool 1 - Spring control arm 2 - Rubber bushing 2b - Bearing shell collar 3k - Bearing seat edge 4 - Suspension strut

01 - Extraction and installation tool 1 - Spring control arm 2 - Rubber bushing 3 - Bearing seat 4 - Suspension strut

Removing:

1. Empty suspension strut (4) of rear axle using STAR DIAGNOSIS
2. Partially remove spring control arm (1). Unhook exhaust system on both rear exhaust-rubber mounts. Detach spring control arm from rear axle carrier and swing downwards.
3. Remove rubber mounts (2) using extraction and insertion tool (01)
4. Clean and check bearing seat (3)

Install:

1. Install rubber mounts (2) using extraction and insertion tool (01). Do not squeeze plastic parts (large arrow) of the rubber mount (2). Cracked plastic parts result in corrosion and thus to damage to the rubber mount(2).
2. Check installation position of the rubber mount (2). Carry out visual inspection of distances (small arrows) from outer bearing shell collar (2b) to the bearing seat edge (3k). In the event of unequal distances (small arrows) correct the installation position using the extraction and insertion tool (01).
3. Install spring control arm (1). Unhook exhaust system on both rear exhaust-rubber mounts.
4. Fill the suspension strut (4) using STAR DIAGNOSIS. The wheels must not touch the ground while pressurizing because the air spring bellows in the suspension strut (4) will be destroyed if pressurized with the suspension compressed.
5. Check AIRmatic for leaks.

Torsion bar

Subframe

Identifying the components in this diagram with same nomenclature as above:

Part	Part no.	Image	Description
15	A2203521365 LEMFÖRDER 2240201 (EUR 8)		Control arm bearing, Spring link to rear axle bracket (left and right)

Remove/install spring control arm and replacement of rubber mount

6 - Spring control arm 6b - Rubber bushing 6g - Cover 6j - Suspension strut

1. Raise vehicle with vehicle lift
2. Remove exhaust system at flange connection
3. Detach cover (6g) from spring control arm (6). To do this, pull pin out of expansion rivet and remove expansion rivet from cover and spring control arm.
4. Remove spring control arm (6) from rear axle carrier. Installation: The rear-axle shaft must be horizontal when tightening the nut. Installation: Tighten bolts or nuts as per tightening angle.
5. Remove spring control arm (6) from wheel carrier. Installation: The rear-axle shaft must be horizontal when tightening the nut.
6. Remove suspension strut (6j) from spring control arm (6).

Remove/install spring control arm rubber mount

Removal and installation tool W220589014300

Press W202589044310

Rubber mount A2203521365

Removing:

1. Detach exhaust bracket from rear axle carrier.
2. Mount sleeve (068b) on bracket (068a).
3. Position removal and insertion tool using thrust piece (068c) and press (010h) on rear axle carrier.
4. Fix press (010h) and thrust piece (068c) in position by tightening the hand wheel (068e). Pay attention to the chamfer (arrow) on the sleeve (068b). It must fit exactly against the rear axle carrier.
5. Press rubber mount part of the way out until the thrust piece (068c) lies against the rear axle carrier (arrow). To do this screw in the pressure screw (010k) of the press (010h). Pushing out the mount prevents the rubber bearing outer race from expanding. If the rubber mount is seized on the bracket (068a), apply a settling blow.
6. Insert the thrust piece (068d) and press out the rubber mount.

Removal and insertion tool of the rubber mount: To move out the piston, screw in the pressure screw (010k) of the press (010h) until the piston has moved out completely. Due to the short stroke of the press (010h) this process must be repeated approx. 5 times. To do this, the piston is to be moved back by turning back the pressure screw (010k) and simultaneously tightening the hand wheel (068e). The spindle of the hand wheel (068e) must always exert a little pressure onto the press (010h) so that the tools cannot fall out.

Install:

1. Replace sleeve (068b) on bracket (068a) by sleeve (068f).
2. Insert rubber mount (6b) into hole in rear axle carrier.
3. Position removal insertion tool with thrust piece (068g) and press (010h) on rear axle carrier.
4. Fix the press (010h) and thrust piece (068g) in position by tightening the hand wheel (068e). Pay attention to the chamfer (arrow) on the sleeve (068f) It must fit exactly against the rear axle carrier.
5. Press the rubber mount (6b) into the rear axle carrier until the the rear axle carrier (arrow).
6. Mount exhaust bracket on rear axle carrier.

In practice, pressing out the old part might be hard even with a press. Instead, the center part can be removed by drilling rubber around it. The outer cylinder can then be knocked out using hammer drill.

For pressing in the new part M12 screw can be used with 54/44mm pressing tube and 64/54mm receiving tube. Make sure to lubricate the new part with white vaseline, for example.

Center drilled out

Knocking out outer

Old mount removed

Cylinders for pressing in

Pressing in new part

Differential

Replace differential fluid

Load video YouTube YouTube might collect personal data. Privacy Policy ContinueDismiss Mercedes W220 S500 and S430 Differential Fluid Replacement (By Masood)

This video shows all the tools and parts needed to replace the differential fluid on a W220 model along with torque specs.

Tools required:

• Hex socket 14mm
• ~1.6 liters of axle drive oil according to MB 235.7 spec (SWAG 10948785 75W-85 1L x2)

14mm hex socket bit 1/2

SWAG 10948785 75W-85 1L

Procedure:

1. Raise the car making sure that it is even on both axles
2. Unscrew the upper 14mm hex screw
3. Unscrew the lower 14mm hex screw
4. Let the old oil drip in a pan
5. Screw-in the lower 14mm hex screw
6. Pour the new oil via the upper screw hole until the differential is full and the oil starts to drip from the upper hole
7. Screw-in the upper 14mm hex screw

Unscrewing upper screw

Pouring new oil

Shaft

Other

Issues - Rear Drive/Axle Suspension

• Squeaking, creaking noises from the rear axle suspension is a common problem.
• The axlel ball joints that look like bushings lose their internal lubrication.

There is a ball joint at the bottom of each suspension AIRmatic strut and another one at the back of the wheel spider. Four ball joints in total. There is no part number for the bottom strut ball joints but they are the same as the outer ones.

It is recommend to replace both the strut ball joints and the outer ball joints when during replacement.

Load video

YouTube

YouTube might collect personal data. Privacy Policy

ContinueDismiss

W220 squeaking noise from rear suspension.

• Unevenly worn tyres that can not be corrected by wheel alignment.

Uneven Rear Tyre Wear due to Worn Torque Strut (3)

Tools - Rear Suspension

• To remove and replace the bushing a special tool is needed.
• Removal and Installation Tool W202589004300 (see Special Tools page).

DIY Tasks - Rear Suspension

Assessing Wear - Rear Suspension

Use a large shifting spanner (handle 300mm long) to tightly grip each Rear Axle Component in turn. Measure the movement at the end of the spanner handle as force is applied. The results will give an indication of the amount of wear occurring in each axle component.

Typical results for a W220 with 240,000Km;

Indication of Wear Rear Axle Components

Rear Axle Component	Rear Left (RL) Measurements [mm]	Rear Right (RR) Measurements [mm]
Camber Strut (2)	15	10 -15
Torque Strut (3)	20	30
Track Rod (4)	15 - 20	10
Thrust Arm (5)	1 -2	1 -2
Tie Rod (25)	0	0

The conclusion with these results was that the Torque Struts need replacing. Consequently it was decided to replace all possible wear components while the rear end was dismantled. See below for DIY.

Replacing All Worn Components - Rear Suspension

After assessing that the Torque Strut (3) was badly worn and the most likely cause of uneven wear on the inner edge of the rear tyres, the decision was made to replace all components that could wear after 240,000Km life.

All the components in the table above were replaced.

WARNING: Replacing the Torque Strut (3) requires lowering of the complete Rear Suspension Sub-Frame by about 200mm as it is impossible to withdraw the Torque Strut (3) inner bolt without doing so. Consequently before starting make sure to either purchase or manufacture 4 off long bolts which will be used as guide pins to keep the Sub-Frame located whilst it is lowered.

This is one of the original Sub-Frame bolts removed to assess the bolt size, which was M12 x 1,5 x 86.5.

The author found it hard to get M12 x 1.5mm pitch long bolts so manufactured some using existing old stock (bolts from tail shaft refurbishment) welded together to make the required 250mm length.

The next picture shows two of the four guide bolts installed and the Sub-Frame lowered.

Method - Replacing All Worn Rear Suspension Components

1. Jack up the vehicle and place on Jack Stands.
2. Remove the rear wheels.
3. Remove Exhaust Clamps (14mm and 12mm spanners).
4. Reomove Exhaust Cross Piece bolt.
5. Remove Tail Shaft Safety Cross Piece (4 off bolts 14mm spanner).
6. Remove small aluminium Heat Shield (3 off bolts 8mm spanner).
7. Remove rear large aluminium Heat Shield (4 off bolts 8mm spanner).
8. Apply foot parking brake.
9. Remove rear three off Tail Shaft to Differential bolts (E18 and 18mm spanners).
10. Mark position of Tail Shaft Centre Bearing Carrier to body with a felt pen. (Makes installation a breeze.)
11. Loosen two off bolts Tail Shaft Centre Bearing Carrier (13mm spanner).
12. Lower rear end of Tail Shaft.
13. Release foot parking brake.
14. Release Parking Brake cable slack adjuster (5mm Allen Key).
15. Remove Parking Brake cable from centre bracket.
16. Remove rear right (RR) brake pad wear sensor (8mm spanner).
17. Remove RR disc brake calliper and support with wire (2 off bolts 18mm spanner).
18. Remove rear disc holding screw (T7 spanner)
19. Remove RR disc.

    Note it is not necessary to remove the rear parking brake shoes.

20. Remove RL wheel speed sensor and release from all clips.
21. Let the sensor cables hang down.
22. Detach Torque Strut (3) from Wheel Carrier (11/16" AF or 18mm spanner)
23. Mark outer joint of Torque Strut (3) with felt pen with designation Y and arrow pointing up. (Makes installation of new component a breeze.) (Note Torque for installation; M12 bolts 70Nm.)
24. Remove Link Rod (25) top and bottom bolts (5/16" AF or 16mm spanner). Note Torque for installation; 40Nm.)
25. Remove Camber Strut (2) to Wheel Carrier (Torx and 11/16" AF or 18mm spanner) Note Torque for installation; 45Nm + 45 degrees.)
26. Mark Camber Strut (2) outer bush with designation X and arrow pointing up. (Makes installation of new component a breeze.)

    

27. Remove Track Rod Ball Joint (4c) from Wheel Carrier Nut (5/8" AF or 16mm spanner.) Note position of cable bracket on nut side and store on new component.) (Note Torque for installation; 70Nm.)
28. Separate Track Rod Ball Joint (4c) from Wheel Carrier using appropriate tool.
29. Mark position of Track Rod (4c) offset washers on inner bolt. (If installed in the same position, rear wheel alignment should be maintained.)
30. Remove Track Rod (4) inner bolt. (Note Torque for installation; 70Nm.) (Note if required add new 12mm washers to inner end as they had been damaged by wheel aligners.)
31. Measure distance between Camber Strut (2) and Torque Strut (3) before undoing inner bolt. This will be used to set the position of the new components. (Note Torque for installation; 70Nm + 120 degrees.) (Approximately 18mm.)
32. Repeat above steps for RL side.
33. Use a trolley jack placed under the differential to support the Rear Axle Carrier Sub-Frame.
34. One at a time,n remove OEM bolts holding axle carrier to car frame and replace with 250mm Guide pins. (Note Torque for installation; Bolt flange 26mm 60Nm + 90 degrees.)
35. Pop off ball joint for rear height level sensor to torsion bar bracket.
36. Unclip cable near rear height level sensor. Note grommet through floor.
37. Cut plastic tie on cable at AIRmatic ride mechanism.
38. Unclip cable at 3 places to free up more cable.
39. Lower trolley jack keeping Axle Carrier as level as possible until there is access to inner Torque Strut bolt.

    

40. Remove Torque Strut (3) to axle carrier (inner bolt 11/16"AF or 18mm spanner.) (Note Torque for installation; 70Nm + 120 degrees.)
41. Remove Camber Strut (2) to axle carrier (inner bolt). (Note Torque for installation; 70Nm.)
42. Mark outer edge of Thrust Arm (5) with designation Z and arrow pointing up. (Makes installation of new component a breeze.)
43. Mark cover of Thrust Arm (5) as well. (Note hole in cover under rubber bush goes to outside.)
44. Remove Thrust Arm (5).
45. Adjust level of rear half shaft 1 to 2 degrees above horizontal and torque Thrust Arm (5) to rear axle carrier (inner bolt) (70Nm).
46. Torque Thrust ASrm (5) to Wheel Carrier (outer bolt) 45Nm + 45 degrees.)
47. Reverse steps above to install remainder of new components. Note do final torquing of accessible bolts with car at correct road height.

48. Adjust vehicle road height with Star SDS.
49. Get rear wheels aligned.

Resources - Rear Suspension

http://www.benzworld.org/forums/w210-e-class/1602887-diy-r-r-outer-bushing-rear.html

http://www.peachparts.com/shopforum/diesel-discussion/338574-notes-r-r-outer-lca-bushings-w124-others.html

http://www.benzworld.org/forums/w201-190-class/1673624-worn-out-hub-carrier-bushing-3.html

http://www.benzworld.org/forums/w220-s-class/1623753-loud-creaking-rear-03-w220-4matic.html

http://www.benzworld.org/forums/w220-s-class/1695182-w220-04-s600-abc-issue-squeaking.html

How to change subframe bushes: http://forums.mercedesclub.org.uk/showthread.php?t=90826 and http://forums.mercedesclub.org.uk/showthread.php?t=90827 .