Gearshift: Difference between revisions
(→Transmission shifter linkage rod connection: photo of linkage) |
(→Transmission shifter linkage rod connection: added photo of new bushing and clip) |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 23: | Line 23: | ||
|[[File:W220_A0009944360_shifting_rod_to_shift_lever_clip.jpg|thumb|none|Clip (A0009944360)]] | |[[File:W220_A0009944360_shifting_rod_to_shift_lever_clip.jpg|thumb|none|Clip (A0009944360)]] | ||
|[[File:W220_gear_shifting_rod_to_shift_lever.jpg|thumb|none|Gear shifting rod linkage]] | |[[File:W220_gear_shifting_rod_to_shift_lever.jpg|thumb|none|Gear shifting rod linkage]] | ||
|} | |||
{| | |||
|[[File:W220_old_bushing_and_broken_clip_gearshift_linkage.jpg|thumb|none|Old bushing and broken clip]] | |||
|[[File:W220_gearshift_linkage_broken_clip_temporary_fix.jpg|thumb|none|Temporary fix for broken clip]] | |||
|[[File:W220_gearshift_linkage_new_clip_and_bushing.jpg|thumb|none|New bushing and clip]] | |||
|} | |} | ||
| Line 29: | Line 34: | ||
However, it is much easier to replace it from underneath the car. To get access to the rod, a small part of exhaust heat shield has to be removed. | However, it is much easier to replace it from underneath the car. To get access to the rod, a small part of exhaust heat shield has to be removed. | ||
The video below shows how to replace the bushing and clip on W210 from underneath the car. | |||
W220 transmission uses different parts (see above) and on W220 the bushing can be replaced by hand without using any special tool. | |||
{| | {| | ||
|{{#ev:youtube|https://youtu.be/tkNL1TWbii8|320|left|W210 722.6 Linkage Bushing Replacement|frame}} | |{{#ev:youtube|https://youtu.be/tkNL1TWbii8|320|left|W210 722.6 Linkage Bushing Replacement|frame}} | ||
Latest revision as of 18:40, 1 May 2024
Transmission shifter
The M-B Transmission Selector allows the driver to select the required mode for the automatic transmission with the choices being usually;
- Park
- Reverse
- Neutral
- Drive (with a choice for manually selecting higher or lower gears if required)
Transmission shifter linkage rod connection
A very common issue with all W220 transmissions is that the linkage bushing wears out and the metal clip corrodes.
This may result in a situation when gear shifter gets disconnected from transmission rod, thereby preventing to change gears using the gear shifter.
Parts:
- A2109920010 - bushing / shifting rod to shift lever
- A0009944360 - clip / shifting rod to shift lever
 |
 |
 |
 |
 |
 |
The bushing and clip can be replaced from inside the car, but this requires removal of the center console and the gear shifter.
However, it is much easier to replace it from underneath the car. To get access to the rod, a small part of exhaust heat shield has to be removed.
The video below shows how to replace the bushing and clip on W210 from underneath the car. W220 transmission uses different parts (see above) and on W220 the bushing can be replaced by hand without using any special tool.
Transmission shifter stuck in park
A common issue is that the transmission shifter becomes stuck in the park position thus disabling the vehicle.
If you notice it is hard to move the transmission gear from Park to Drive, or that it is not shifting as easily as before, take it as a warning sign and follow the instructions in the following video to replace the little plastic lever inside the shifter assembly before it is stuck in Park and the car has to be towed to a mechanic. This applies to 2000 - 2006 W220 S500, S430, CL500, and 2001-2006 S55 AMG.
Part numbers are 2202679924 (the car in video, 2000 S500) - around $42 from Amazon as of May 2023 - and 2202679724 ($27). Unless you know exactly which to buy, purchase both and return the one that doesn't fit.
In case of emergency, a stuck shifter can be moved out from the park position using force:
The most common cause for this problem is a plastic lever that breaks inside the shifter. Another cause for the problem could be a defective brake light switch (or blown fuse f16 - stop signal switch).
A broken plastic lever can be replaced with an aftermarket metal lever (~30 EUR from eBay using the keyword "W220 trans shifter lever"). To properly replace the lever, a rivet gun and 3 aluminium rivets are needed. The original rivets are of size 3.2x12mm, but in practice 3.2x8mm rivets will work as well.
 |
 |
The broken plastic part can be removed without replacing it, but doing so defeats the brake/shifter interlock, as it will be possible to move the shift lever at all times even with ignition on or off. If you plan to leave unattended children in the car, this fix may not be right for you in which case you should replace the broken pieces to restore the safety feature to its original condition.
Shift knob
Removing shift knob
- Unlock the shifter knob by turning conterclockwise on the chrome part of the knob until it stops, only 1/4 of a turn is necessary.
- Lift the knob straight up off the shaft. Do this in N position if you have large hands so when the knob is coming off of the shaft you don't hit the COMAND screen and center console.
Fixing loose shift knob
Incorrect removal procedure by trying to twist the knob, will damage the plastic core of the gear knob and knob will become loose. One way to fix a loose knob is to use type around the shaft. The idea is to build up some thickness on the shaft. Do not wrap anything around the chrome bezel area, it won't do anything but stop the knob returning to it's original locked position. Only wrap the top part of the shaft.
 |
 |
Dissecting shift knob
- Use cord to tie up the plastic core and to pull the plastic ring off.
- Pour in some alcohol in between the wood part and the plastic core. Alcohol will soften the glue. Tier it gently until it comes off.
- KEYLESS-GO button is attached from the bottom with two T6 screws.
 |
 |
 |
 |
 |
 |