Rearview mirror: Difference between revisions
(→Removing inside rearview mirror: photo of retaining plate and spring) |
(→Reading lamps: part number for bulb) |
||
| Line 225: | Line 225: | ||
==Reading lamps== | ==Reading lamps== | ||
The left reading lamp (A67e1) and right reading lamp (A67e2) are integrated in the mirror housing. | The left reading lamp (A67e1) and right reading lamp (A67e2) are integrated in the mirror housing. | ||
The bulb used is 12V/6W (A0025443894). | |||
For some rearview mirrors the reading lamp cover is attached to the lamp housing, while for others the cover is attached to mirror housing (see below). | For some rearview mirrors the reading lamp cover is attached to the lamp housing, while for others the cover is attached to mirror housing (see below). | ||
Revision as of 22:17, 19 November 2016
Location
The interior rearview mirror unit (A67) is located on the overhead control panel control module (N70) centered at front of the headliner.
|
|
Part numbers
There are several versions of W220 rearview mirrors. Left-hand drive vehicles and right-hand drive vehicles have different rearview mirrors. Similarly, there are different versions of rearview mirrors depending on the option codes vehicle is equipped with - garage door opener (option code 231/232), dimming function (option code 249), memory function (option code 275) and telephone or voice control system (option codes 349/359/380/381/382/383/384/385/386/388).
Left-hand drive vehicles
| Part No. | Notes | Front | Bottom | Top |
|---|---|---|---|---|
| A2208100217 | To Date: 30/09/2003, option 232+249+275, replaced by A2208102817 | 
|
|
|
| A2208102817 | To Date: 30/09/2003, option 232+249+275 | 
|
|
|
| A2208100517 | To Date: 30/09/2003 | 
|
|
|
| A2208102617 | From Date: 31/10/2002, To Date: 30/09/2003, option 804, From Date: 30/09/2003 not valid for option 383/386/388 | |||
| A2208100017 | To Date: 30/09/2003, option 249 | 
|
|
|
| A2208102717 | From Date: 30/09/2003, option 349/380/381/382/383/384/385/386/388 | |||
| A2208101317 | From Date: 31/10/2002, To Date: 30/09/2003, option 249+804 | |||
| A2208104017 | From Date: 30/09/2003, option 249 | |||
| A2208101717 | From Date: 31/10/2002, To Date: 30/09/2003, option 232+249+804+[380/381/382/383/384/385] | 
|
|
|
| A2208103617 | From Date: 30/09/2003, option 232+249+[359/380/381/382/383/384/386/388] | 
|
|
|
| A2208100317 | To Date: 30/09/2003, Replaced by: A2208101817, option 231+249+[275] | 
|
|
|
| A2208101817 | To Date: 30/09/2003, 231+249+[275] | 
|
|
|
| A2208101517 | From Date: 31/10/2002, To Date: 30/09/2003, option 231+249+804 | |||
| A2208103817 | From Date: 30/09/2003, option 231+249 | |||
| A2208102017 | From Date: 31/10/2002, option 249+[349/380/381/382/383/384/386/388] | 
|
|
|
| A2208103517 | (not in EPC, but seems to be the successor of A2208102017) | 
|
|
|
| A2208102217 | To Date: 30/09/2003, option 231+249+[349/380/381/382/383/385]+804 | |||
| A2208103317 | From Date: 30/09/2003, option 231+249+[380/381/382/383/386/388] | 
|
|
|
Right-hand drive vehicles (UK)
| Part No. | Notes |
|---|---|
| A2208100117 | option 275 |
| A2208101417 | From Date: 31/10/2002, To Date: 30/09/2003, option 249+804 |
| A2208103917 | From Date: 30/09/2003, option 249 |
| A2208100417 | To Date: 30/09/2003, Replaced by: A2208101917, option 231+275 |
| A2208101917 | To Date: 30/09/2003, Replaced by: A2208101917, option 231+275 |
| A2208101617 | From Date: 31/10/2002, To Date: 30/09/2003, option 231+249+804 |
| A2208103717 | From Date: 30/09/2003, option 231+249 |
| A2208102117 | From Date: 31/10/2002, To Date: 30/09/2003, option 249+[349/380/381/382/383]+804 |
| A2208103417 | From Date: 30/09/2003, option 249+[380/381/382/383/386/388] |
| A2208102317 | To Date: 30/09/2003, option 231+249+[349/380/381/382/383]+804 |
| A2208103217 | From Date: 30/09/2003, option 231+249+[380/381/382/383/386/388] |
Design
|
|
Tasks:
- The inside rearview mirror (A67) can be adjusted manually.
- Depending on the equipment (see below), the manually adjusted mirror position can be stored, called up later with the memory function and actuated automatically.
- The mirror lens of the inside rearview mirror (A67) can be electro-chromatically dimmed. Dimming is accomplished according to the variables measured by the mirror dimming forward sensor (A67h1) and mirror dimming backward sensor (A67h2).
- The left reading lamp (A67e1) and right reading lamp (A67e2) as well as the ambient light (A67e3) are also integrated in the mirror housing.
Wiring diagram
Rearview mirror is connected to the overhead control panel control module (N70).
Ambient/vanity lamp
The ambient lamp (A67e3) is a bright LED (powered by 12 volts) located in the interior rear view mirror (A67). It serves for illumination of the center console.
The ambient lamp is switched on automatically when C.15r is switched on and switched off automatically when C.15r is switched off (i.e., the ambient lamp is on when the ignition is on).
The ambient lamp (A67e3) is controlled directly by the overhead control panel control module (N70). The overhead control panel control module (N70) receives the information "Status c.15r" for this purpose via the CAN bus from the electronic ignition/starter switch control module (N73).
The ambient lamp is independent of the automatic light switch daylight sensor (B32/1) and the position of the door contact ON and OFF switch (N70s3).
 |
 |
Reading lamps
The left reading lamp (A67e1) and right reading lamp (A67e2) are integrated in the mirror housing. The bulb used is 12V/6W (A0025443894).
For some rearview mirrors the reading lamp cover is attached to the lamp housing, while for others the cover is attached to mirror housing (see below).
 |
 |
 |
Automatic dimming function
For vehicles with option code 249 - INSIDE AND OUTSIDE MIRROR AUTOMATIC DIMMING the interior rearview mirror unit (A67) can be dimmed electro-chromatically. For this purpose, a layer of electrolyte gel is located in the mirror glass between the reflector and the cover lens. Voltage connected to the gel modifies its permeability to light. The light reaching the surface of the mirror is reflected to a greater or lesser extent due to the magnitude of the actuating voltage. The actuating voltage is controlled by the electronic circuitry in the interior rearview mirror. This procedure is subject to the ambient light and the light reaching the mirror.
These two input variables are sensed by the ambient light sensor (A67h2) in the mirror housing (rear side) and the automatic dimming interior rearview mirror sensor (A67h1) in the mirror glass of the interior rearview mirror unit (A67).
 |
 |
If an interior light is switched on or the reverse gear (CAN message) is engaged, the interior rearview mirror is always switched to a brighter setting. This is accomplished by an additional signal lead from the overhead control panel control module (N70) to the interior rearview mirror unit (A67).
Function prerequisites:
- Voltage not too low or too high
- C.15R or C.15 ON
The interior rearview mirror unit (A67) serves also as master for the automatic dimming exterior rearview mirror (driver's side).
Driver-side exterior rearview mirror automatic dimming feature
The inside rearview mirror (A67) in combination with the overhead control panel control module (N70) serves as master for dimming the electrically adjustable and heated left outside mirror (M21/1) (special equipment).
|
|
Function prerequisites:
- Voltage not too low or too high
- C.15R or C.15 ON
The light reaching the surface of the mirror is reflected to a greater or lesser extent depending on the magnitude of the control voltage. The control voltage is regulated by the interior rearview mirror unit (A67) (master) and the overhead control panel control module (N70). Two discrete leads are connected to the left front door control module (N69/1) for this purpose (vehicles with right-hand steering: right front door control module ((N69/2)).
Regulation is accomplished depending on the ambient light and the light reaching the mirror. These two variables are measured by the ambient light sensor (A67h2) in the interior rearview mirror housing (rear) and the automatic dimming interior rearview mirror sensor (A67h1) in the mirror glass in the interior rearview mirror unit.
If one of the interior lights is switched on or the CAN message "Reverse gear engaged" is received from the electronic ignition/ starter switch control module (N73), the exterior rearview mirror as well as interior rearview mirror become brighter.
Memory feature
For vehicles with option code 275 - MEMORY PACKAGE (DRIVER SEAT, STRG. COL., MIRROR) the inside rearview mirror (A67) can be adjusted automatically with the memory function, i.e. stored mirror position can be called up. For this purpose, two DC motors, a vertical adjustment motor (A67m1) and a horizontal adjustment motor (A67m2) are present in the housing actuated by the overhead control panel control module (N70). The vertical position potentiometer (A67r1) and horizontal position potentiometer (A67r2) are located next to the motors for position recognition.
Note: As of chassis 392659 (10/2003) the inside rearview mirror memory function is no longer part of the memory package (seat adjustment, steering wheel height adjustment and outside mirror adjustment). The memory feature for the electrical inside rearview mirror can no longer be ordered and is no longer installed in the series production of the models specified above.
This is the reason why vehicles produced after 10/2003 may have this error code present:
| Error Code | Description |
|---|---|
| B10B4 | Component A67r1 (Vertical position potentiometer) has Open circuit or Short circuit to ground. This fault can be ignored as of manufacture year 10.2003. |
| B10B6 | Component A67r2 (Horizontal position potentiometer) has Open circuit or Short circuit to ground. This fault can be ignored as of manufacture year 10.2003. |
Hands-free system microphone group
 |
On vehicles as of 01/09/2003 with telephone or with telephone and voice control system (VCS), a hands-free system microphone group (A67b1) is integrated in the inside rearview mirror (A67). The following functions can be performed via the hands-free system microphone group (A67b1):
- Voice input for making telephone calls using the hands-free system
- Voice input for voice control system (VCS) (interactive dialog with VCS)
The signals are transmitted to the hands-free system control module (A35/1) or the voice control module (A35/11) via the hands-free system microphone group (A67b1).
 |
 |
 |
 |
 |
 |
 |
 |
 |
The casing for rearview mirror with embedded microphone group is bigger in volume than the usual mirror casing (see the picture above). The microphone group module has a separate 6-wire cable that connects to voice control module extension wire that is centered under the headliner.
Garage door opener
Vehicles with option code 231 - GARAGE DOOR OPENER or 232 - GARAGE DOOR OPENER WITH 284 - 390 MHZ FREQUENCY have garage door opener buttons integrated in the rearview mirror.
|
|
Garage door opener, function
The garage door opener consists of an adaptive radio remote control with three transmit buttons. With these three buttons: Button 1 garage door opener (A67s1), button 2 garage door opener (A67s2) or button 3 garage door opener (A67s3) it is possible to activate various receivers for the opening and closing system of the doors and gates.
Program remote control
|
Function requirements:
|
In order to save the vehicle battery, the transmitter switches off automatically in the learn-in mode, if programming is not accomplished after approx. 100 seconds.
Transmitter mode
If button 1 garage door opener (A67s1), button 2 garage door opener (A67s2) or button 3 garage door opener (A67s3) is actuated, the signal learned in for this memory space is transmitted activating the associated garage door drive.
The garage door opener signal has a range of at least 15 m.
The transmitter buttons (1) as well as the transmitter for opening the garage door are integrated into the inside rearview mirror (2).
Erasing
- C. 15 R or c. 15 ON.
- Press button 1 of garage door opener (A67s1) and button 3 of garage door opener (A67s3) simultaneously for approx. 20 s. The garage door opener indicator lamp (A67e4) starts flashing.
- Release button 1 on garage door opener (A67s1) and button 3 on garage door opener (A67s3) when garage door opener indicator lamp (A67e4) is flashing within 10 s after it starts flashing. The existing data of the memory locations is erased.
The memories are erased by actuating the button 1 garage door opener (A67s1) and button 3 garage door opener (A67s3) for longer than 20 ms. Successful erasure of all memory locations is indicated for approx. 10 s by the LED flashing rapidly.
Removing inside rearview mirror
Rearview mirror is attached to the sealing using a spring mechanism. Hence the mirror can be detached and reattached simply by force.
 |
 |
|
|
|
- Remove overhead control panel control module with front dome lamp
- Unclip paneling (2) on inside rearview mirror
- Remove paneling (3)
- Remove inside rearview mirror (1) by inserting screwdriver between inside rearview mirror (1) and retaining plate (4) and prying out inside rearview mirror
- Install in opposite order
Rain sensor cover
Rain sensor cover Part no. A2208110007 is universal for all types of rear view mirrors. The only difference is in color. Facelift models use different tone of gray - alpaca gray.
 |
 |
 |
 |
Mirror cover
| Part No. | Notes | Front | Back |
|---|---|---|---|
| A2208110171 | 
|
| |
| A2208100764 | option 278/316/317/329/852/853/854 | 
|
|
| A2208100464 | Left-hand drive, option 347/349/855/930 | 
|
|
| A2208101564 | Left-hand drive, option 349+804,383+804,384+804,359,383,384 | 
|
|
| A2208100564 | Right-hand drive, option 349/855 | ||
| A2208101664 | Right-hand drive, option 349+804,383+804,383,349 |
Disassembling A2208100017
Parts of rearview mirror A2208100017 (dimming function + memory function).
 |
 |
 |
 |
 |
 |
 |
 |
Disassembling A2208103517
Parts of rearview mirror A2208103517 (dimming function + microphone group).
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Rearview mirror with memory function and microphone group
There are no rearview mirrors that have both, the memory function and microphone group embedded (the reason could be that memory function was discontinued at 10/2003, before the microphone group in mirror was introduced). However, it is possible to construct one from two mirrors by joining mirror cover that has microphone group embedded to mirror that has memory function. The only challenge is to pull the microphone group wire through the mirror holder. To do that, the wire connector has to be detached from the wire (see below).
 |
 |
 |
 |