Car Solutions RGB-LE-V3.1: Difference between revisions

Latest revision as of 19:06, 9 October 2017

Description

Yet another video input interface for Mercedes S-Class W220. Useful for rear view camera installation.

The interface is for MOST-based COMANDs. It will not work on widescreen D2B based COMANDs.

Car video interface for Mercedes-Benz W220 allows connection and usage of external video devices such as DVD player, TV tuner, rear view camera, etc. on your built-in monitor.

Input:

Composite video (CVBS) input (external video source) x 2
Composite video (CVBS) input (rear camera source - automatically switchable) x 1
Analog RGB input (car commander original monitor output) x 1
Analog RGB input (aftermarket navigation system output) (option) x 1

Output:

Composite video (CVBS) output (video out for headrest monitor installation) x 1
RGB output (to W220 COMAND) x 1
Audio select output x 1

Switch input mode:

Possible to mute each input by operating DIP switches.
Possible to switch input source with remote control or toggle switch.
Rear view camera mode - rear view camera is switched on when the vehicle is reversing (not possible to switch to the rear mode with the toggle or the remote control).

Package Contents

RGB Converter

Dimensions: horizontal - 129mm, vertical - 75mm, height - 21mm.

POWER

This port is used to connect power cable with fuse box.

RGB converter accepts input power: 8V~18V DC. Power consumption max 5 watt. Installed fuse has 5A 250V rating. Measured power consumption around 230mA (2.7W) of current, therefore, it should not be left connected directly to the battery. It is safe to connect the interface to ignition wire (e.g., cigarette lighter wire) since if not connected to power source, the COMAND will work in pass-through mode acting as if multimedia interface is not installed.

Wire	Description
	not connected
read	ACC (power)
gray	REV GEAR LAMP (activates rear view camera input)
blue	FMTX antenna (???)
orange	I-Drive (???)
black	GND (ground)

MODE

This port is used to connect video input source toggle switch.

AV source switching order: OEM - RGB - AV1 - AV2.

Note that rear camera av source is not switchable using input source switching. As a workaround the rear camera can be connected also to CVBS1 or CVBS2.

Note that RGB converter makes loud clicking noise when switching between sources.

IR

This port is used to connect infrared receiver for the remote control. For the 4-pin connector only 3 pins are used.

Remote Control

Key	Function
POWER	Not used
PIP	Not used
MENU	OSD implementation
OK	Make selection
UP	Move upward
DOWN	Move downward
LEFT	Move leftward (press 2 seconds long - factory mode implementation)
RIGHT	Move rightward (press 2 seconds long - factory mode implementation and reset)

Remote control is powered by CR2025 battery.

In practice only the "OK" button works, which switches between video sources (the same way as the toggle switch).

V1

This port is used to connect the first video input (CVBS1).

V2

This port is used to connect the second video input (CVBS1).

R/V

This port is used to connect the rear view camera video input.

V-OUT

This port outputs currently selected video input. Can be used to send currently displayed video to headrest monitor.

NAVI (IN)

This port is used to connect navigation input (analog RGB).

Wire	Description
	not connected
	not connected
black	GND
white	SYNC
blue	B DATA
green	G DATA
red	R DATA

OEM (IN)

This port is used to connect original video input (analog RGB).

Wire	Description
black	GND
white	SYNC
blue	B DATA
green	G DATA
red	R DATA

RGB (OUT)

This port connects to the RGB interface installed in W220 COMAND. The package comes with additional universal RGB connector (not needed for multimedia interface use with COMAND).

Wire	Description
blue	B DATA
green	G DATA
red	R DATA
while	SYNC
black	GND
yellow	ACC
orange	VIDEO S/W
	not connected

DIP S/W

DIP switch allows to skip some inputs which are not connected.

PIN	Name	Description
1	RGB INPUT SKIP	ON: Skipping RGB mode
2	CVBS1 MUTE	ON: Skipping CVBS1 input
3	CVBS2 MUTE	ON: Skipping CVBS2 input
4	CAN	ON: When installing to the Cayenne
5	OEM MUTE	ON: Skipping OEM input
6	INTERLACE	ON: Non-interlace
7	REAR MODE	ON: External rear camera installed
8	SYNC ON GREEN	ON: Sync on green (RGSB)

OEM MUTE will make multimedia interface always on and video from the COMAND itself will not be shown.

If the displayed screen vibrates, try to operate DIP switch number 6 (interlace mode) after turning power off.

SEL (OUT)

This 3-PIN port gives voltage on one PIN at a time, depending on the video source that is currently selected - REAR-SEL (white), AV1-SEL (yellow), NAVI-SEL (gray). For example, 12V output is on yellow wire when AV1 input source is chosen. Can be used to activate appropriate audio output.

LED

First LED lamp indicates that interface is on.

Second LED lamp indicates that AV sources connected work well.

Interface Connections

RGB interface board for W220 COMAND has a simple task to hijack COMAND video output when video input is received from RGB converter.

Installation

Remove the COMAND from the vehicle using COMAND removal instructions.

Unscrew 2 chassis cover screws at top of radio.

Unscrew 4 on the rear of the unit, remove cover from top of unit.

Begin by unscrewing the cassette player mechanism from the unit. There are 2 screws holding it in place.

Unscrew the mechanism's other mounting screw.

Loosen the ribbon cable attachment clip with a small screwdriver and carefully remove the cassette player mechanism.

Continue removing the remaining screws to remove the upper motherboard.

Using needle nosed pliers twist the metal clip that attaches to the upper motherboard.

Using a small screwdriver unscrew the ribbon cable from the motherboard.

Unclip the plastic connector from both sides.

Disconnect ribbon cable from the motherboard.

Mount converter on top of radio with 2 sided tape.

Troubleshooting

If COMAND display works fine, but all video sources produce flickering image shown below, the ribbon cables are connected in the opposite order.

@@ Line 1: / Line 1: @@
 == Description ==
 Yet another [[COMAND_Multimedia_interface|video input interface]] for Mercedes S-Class W220. Useful for [[rear view camera]] installation.
+The interface is for [[MOST]]-based [[MOST COMAND-APS|COMANDs]].
+'''It will [[COMAND_Multimedia_interface|not work]] on widescreen [[D2B]] based [[D2B COMAND|COMANDs]].'''
 Price: [http://car-solutions.com/en/car-video-interface-for-mercedes-benz-s-class-w220.php USD 190].
@@ Line 6: / Line 9: @@
 Car video interface for Mercedes-Benz W220 allows connection and usage of external video devices such as DVD player, TV tuner, rear view camera, etc. on your built-in monitor.
-Input: multi video interface:
+Input:
-* CVBS input (external video source) x 2
+* [https://en.wikipedia.org/wiki/Composite_video Composite video] (CVBS) input (external video source) x 2
-* CVBS input (rear camera source) x 1
+* [https://en.wikipedia.org/wiki/Composite_video Composite video] (CVBS) input (rear camera source - automatically switchable) x 1
 * Analog RGB input (car commander original monitor output) x 1
-* Analog RGB input (navigation system output) (option) x 1
+* Analog RGB input (aftermarket navigation system output) (option) x 1
 Output:
-* CVBS output (video out for headrest monitor installation) x 1
+* [https://en.wikipedia.org/wiki/Composite_video Composite video] (CVBS) output (video out for headrest monitor installation) x 1
-* RGB output (LCD operation) x 1
+* RGB output (to W220 COMAND) x 1
 * Audio select output x 1
 Switch input mode:
-* Possible to mute each input by operating DIP S/W
+* Possible to mute each input by operating DIP switches.
-* Possible to switch input mode with remote control or toggle switch.
+* Possible to switch input source with remote control or toggle switch.
-* Rear view camera mode: rear view camera is switched when the vehicle is reversing (impossible to switch to the rear mode with the toggle or the remote control)
+* Rear view camera mode - rear view camera is switched on when the vehicle is reversing (not possible to switch to the rear mode with the toggle or the remote control).
 == Package Contents ==
@@ Line 30: / Line 33: @@
 {|
 |[[File:W220_Car_Solutions_RGB-LE-V3.1_power_cable.jpg|thumb|none|Power cable.]]
-|[[File:W220_Car_Solutions_RGB-LE-V3.1_mode_switch_button.jpg|thumb|none|Mode switch button.]]
+|[[File:W220_Car_Solutions_RGB-LE-V3.1_mode_switch_button.jpg|thumb|none|Mode switch button. Connects to port "SEL (OUT)".]]
-|[[File:W220_Car_Solutions_RGB-LE-V3.1_RGB_cable_IR_cable.jpg|thumb|none|Cable from RGB board to converter. IR sensor cable.]]
+|[[File:W220_Car_Solutions_RGB-LE-V3.1_RGB_cable_IR_cable.jpg|thumb|none|RGB out cable. IR sensor cable.]]
 |}
 {|
-|[[File:W220_Car_Solutions_RGB-LE-V3.1_cable1.jpg|thumb|none|]]
+|[[File:W220_Car_Solutions_RGB-LE-V3.1_cable1.jpg|thumb|none|Selected mode output cable.]]
-|[[File:W220_Car_Solutions_RGB-LE-V3.1_cable2.jpg|thumb|none|]]
+|[[File:W220_Car_Solutions_RGB-LE-V3.1_cable2.jpg|thumb|none|RGB in cable.]]
+|}
+== RGB Converter ==
+[[File:Universal_RGB_converter_LE_top_side.jpg|600px]]
+[[File:Universal_RGB_converter_LE.jpg|600px]]
+[[File:Universal_RGB_converter_LE_bottom_side.jpg|600px]]
+Dimensions: horizontal - 129mm, vertical - 75mm, height - 21mm.
+=== POWER ===
+This port is used to connect power cable with fuse box.
+{|
+|[[File:Universal_RGB_converter_LE_power_cable_fuse_box.jpg|thumb|none|Power cable and fuse box.]]
+|[[File:Universal_RGB_interface_LE_fuse_box_open.jpg|thumb|none|Fuse box open.]]
+|}
+RGB converter accepts input power: 8V~18V DC.
+Power consumption max 5 watt.
+Installed fuse has 5A 250V rating.
+Measured power consumption around 230mA (2.7W) of current, therefore, it should not be left connected directly to the battery. It is safe to connect the interface to ignition wire (e.g., cigarette lighter wire) since if not connected to power source, the COMAND will work in pass-through mode acting as if multimedia interface is not installed.
+{| class="wikitable"
+! Wire
+! Description
+|-
+|
+|not connected
+|-
+|read
+|ACC (power)
+|-
+|gray
+|REV GEAR LAMP (activates rear view camera input)
+|-
+|blue
+|FMTX antenna (???)
+|-
+|orange
+|I-Drive (???)
+|-
+|black
+|GND (ground)
+|}
+=== MODE ===
+This port is used to connect video input source toggle switch.
+[[File:Universal_RGB_converter_LE_mode_switch_cable.png]]
+AV source switching order: OEM - RGB - AV1 - AV2.
+Note that rear camera av source is not switchable using input source switching.
+As a workaround the rear camera can be connected also to CVBS1 or CVBS2.
+Note that RGB converter makes loud clicking noise when switching between sources.
+=== IR ===
+This port is used to connect infrared receiver for the remote control. For the 4-pin connector only 3 pins are used.
+[[File:Universal_RGB_interface_LE_infrared_cable.jpg|thumb|none|Infrared cable.]]
+==== Remote Control ====
+{|
+|[[File:Universal_RGB_converter_LE_remote_control.jpg|thumb|Remote control. Size:85*40*8 (mm).]]
+|
+{| class="wikitable"
+! Key
+! Function
+|-
+|POWER
+|Not used
+|-
+|PIP
+|Not used
+|-
+|MENU
+|OSD implementation
+|-
+|OK
+|Make selection
+|-
+|UP
+|Move upward
+|-
+|DOWN
+|Move downward
+|-
+|LEFT
+|Move leftward (press 2 seconds long - factory mode implementation)
+|-
+|RIGHT
+|Move rightward (press 2 seconds long - factory mode implementation and reset)
+|}
+|}
+Remote control is powered by CR2025 battery.
+In practice only the "OK" button works, which switches between video sources (the same way as the toggle switch).
+=== V1 ===
+This port is used to connect the first video input (CVBS1).
+=== V2 ===
+This port is used to connect the second video input (CVBS1).
+=== R/V ===
+This port is used to connect the rear view camera video input.
+=== V-OUT ===
+This port outputs currently selected video input.
+Can be used to send currently displayed video to headrest monitor.
+=== NAVI (IN) ===
+This port is used to connect navigation input (analog RGB).
+[[File:Universal_RGB_interface_LE_NAVI_in_cable.jpg|thumb|none|NAVI in cable.]]
+{| class="wikitable"
+! Wire
+! Description
+|-
+|
+|not connected
+|-
+|
+|not connected
+|-
+|black
+|GND
+|-
+|white
+|SYNC
+|-
+|blue
+|B DATA
+|-
+|green
+|G DATA
+|-
+|red
+|R DATA
 |}
+=== OEM (IN) ===
+This port is used to connect original video input (analog RGB).
+[[File:Universal_RGB_interface_LE_OEM_in_cable.jpg|thumb|none|OEM in cable.]]
+{| class="wikitable"
+! Wire
+! Description
+|-
+|black
+|GND
+|-
+|white
+|SYNC
+|-
+|blue
+|B DATA
+|-
+|green
+|G DATA
+|-
+|red
+|R DATA
+|}
+=== RGB (OUT) ===
+This port connects to the RGB interface installed in W220 COMAND.
+The package comes with additional universal RGB connector (not needed for multimedia interface use with COMAND).
+[[File:Universal_RGB_interface_LE_RGB_out_cable.jpg|thumb|none|RGB out cable.]]
+{| class="wikitable"
+! Wire
+! Description
+|-
+|blue
+|B DATA
+|-
+|green
+|G DATA
+|-
+|red
+|R DATA
+|-
+|while
+|SYNC
+|-
+|black
+|GND
+|-
+|yellow
+|ACC
+|-
+|orange
+|VIDEO S/W
+|-
+|
+|not connected
+|}
+=== DIP S/W ===
+DIP switch allows to skip some inputs which are not connected.
+[[File:RGB_converter_DIP_switch.jpg|400px]]
+{| class="wikitable"
+! PIN
+! Name
+! Description
+|-
+|1
+| RGB INPUT SKIP
+| ON: Skipping RGB mode
+|-
+|2
+| CVBS1 MUTE
+| ON: Skipping CVBS1 input
+|-
+|3
+| CVBS2 MUTE
+| ON: Skipping CVBS2 input
+|-
+|4
+| CAN
+| ON: When installing to the Cayenne
+|-
+|5
+| OEM MUTE
+| ON: Skipping OEM input
+|-
+|6
+| INTERLACE
+| ON: Non-interlace
+|-
+|7
+| REAR MODE
+| ON: External rear camera installed
+|-
+|8
+| SYNC ON GREEN
+| ON: Sync on green (RGSB)
+|}
+OEM MUTE will make multimedia interface always on and video from the COMAND itself will not be shown.
+If the displayed screen vibrates, try to operate DIP switch number 6 (interlace mode) after turning power off.
+=== SEL (OUT) ===
+[[File:Universal_RGB_interface_LE_SEL_out_cable.jpg|thumb|none|SEL out cable.]]
+This 3-PIN port gives voltage on one PIN at a time,
+depending on the video source that is currently selected
+- REAR-SEL (white), AV1-SEL (yellow), NAVI-SEL (gray).
+For example, 12V output is on yellow wire when AV1 input source is chosen.
+Can be used to activate appropriate audio output.
+=== LED ===
+First LED lamp indicates that interface is on.
+Second LED lamp indicates that AV sources connected work well.
 == Interface Connections ==
+RGB interface board for W220 COMAND has a simple task to hijack COMAND video output when video input is received from RGB converter.
 [[File:W220_Car_Solutions_RGB_interface_connections.jpg|none]]
@@ Line 71: / Line 353: @@
 |[[File:W220_Car_Solutions_RGB-LE-V3.1_install15c.jpg|thumb|none|Connect RGB cable and run outside of unit.]]
 |[[File:W220_Car_Solutions_RGB-LE-V3.1_install16.jpg|thumb|none|Mount converter on top of radio with 2 sided tape.]]
+|[[File:W220_Car_Solutions_RGB-LE-V3.1_install17.jpg|thumb|none|Video input source switch button.]]
 |}
@@ Line 79: / Line 362: @@
 [[File:W220_CT90-MC04_RGB_cable_installation.jpg|thumb|none|Disconnect the wires from the connector to pull the cable through the hole.]]
 -->
+== Troubleshooting ==
+If COMAND display works fine, but all video sources produce flickering image shown below, the ribbon cables are connected in the opposite order.
+[[File:W220_COMAND_screen_flicker_Car_Solutions_RGB-LE-V3.1.jpg|500px]]