Car Solutions RGB-LE-V3.1

Description

Yet another video input interface for Mercedes S-Class W220. Useful for rear view camera installation.

The interface is for MOST-based COMANDs. It will not work on widescreen D2B based COMANDs.

Price: USD 190.

Car video interface for Mercedes-Benz W220 allows connection and usage of external video devices such as DVD player, TV tuner, rear view camera, etc. on your built-in monitor.

Input:

• Composite video (CVBS) input (external video source) x 2
• Composite video (CVBS) input (rear camera source - automatically switchable) x 1
• Analog RGB input (car commander original monitor output) x 1
• Analog RGB input (aftermarket navigation system output) (option) x 1

Output:

• Composite video (CVBS) output (video out for headrest monitor installation) x 1
• RGB output (to W220 COMAND) x 1
• Audio select output x 1

Switch input mode:

• Possible to mute each input by operating DIP switches.
• Possible to switch input source with remote control or toggle switch.
• Rear view camera mode - rear view camera is switched on when the vehicle is reversing (not possible to switch to the rear mode with the toggle or the remote control).

Package Contents

RGB converter.

RGB board with flat cables.

Remote control.

Power cable.

Mode switch button. Connects to port "SEL (OUT)".

RGB out cable. IR sensor cable.

Selected mode output cable.

RGB in cable.

RGB Converter

Dimensions: horizontal - 129mm, vertical - 75mm, height - 21mm.

POWER

This port is used to connect power cable with fuse box.

Power cable and fuse box.

Fuse box open.

RGB converter accepts input power: 8V~18V DC. Power consumption max 5 watt. Installed fuse has 5A 250V rating. Measured power consumption ~230mA (2.7W).

Wire	Description
	not connected
read	ACC (power)
gray	REV GEAR LAMP (activates rear view camera input)
blue	FMTX antenna (???)
orange	I-Drive (???)
black	GND (ground)

MODE

This port is used to connect mode switch cable with switch button.

AV source switching order: OEM - RGB - AV1 - AV2 - AV3.

IR

This port is used to connect infrared receiver for the remote control. For the 4-pin connecter only 3 pins are used.

Infrared cable.

Remote Control

Remote control. Size:85*40*8 (mm).

Key Function POWER Not used PIP Not used MENU OSD implementation OK Make selection UP Move upward DOWN Move downward LEFT Move leftward (press 2 seconds long - factory mode implementation) RIGHT Move rightward (press 2 seconds long - factory mode implementation and reset)

Remote control is powered by CR2025 battery.

V1

This port is used to connect first video input (CVBS1).

V2

This port is used to connect second video input (CVBS1).

R/V

This port is used to connect rear view camera.

V-OUT

This port outputs currently selected video input. Can be used to send currently displayed video to headrest monitor.

NAVI (IN)

This port is used to connect navigation input (analog RGB).

NAVI in cable.

Wire	Description
	not connected
	not connected
black	GND
white	SYNC
blue	B DATA
green	G DATA
red	R DATA

OEM (IN)

This port is used to connect original video input (analog RGB).

OEM in cable.

Wire	Description
black	GND
white	SYNC
blue	B DATA
green	G DATA
red	R DATA

RGB (OUT)

This port connects to the RGB interface installed in W220 COMAND. The package comes with additional universal RGB connector (not needed for multimedia interface use with COMAND).

RGB out cable.

Wire	Description
blue	B DATA
green	G DATA
red	R DATA
while	SYNC
black	GND
yellow	ACC
orange	VIDEO S/W
	not connected

DIP S/W

DIP switch allows to skip some inputs which are not connected.

PIN	Name	Description
1	RGB INPUT SKIP	ON: Skipping RGB mode
2	CVBS1 MUTE	ON: Skipping CVBS1 input
3	CVBS2 MUTE	ON: Skipping CVBS2 input
4	CAN	ON: When installing to the Cayenne
5	OEM MUTE	ON: Skipping OEM input
6	INTERLACE	ON: Non-interlace
7	REAR MODE	ON: External rear camera installed
8	SYNC ON GREEN	ON: Sync on green (RGSB)

If the displayed screen vibrates, try to operate DIP switch number 6 (interlace mode) after turning power off.

SEL (OUT)

SEL out cable.

This 3-PIN port gives voltage on one PIN at a time, depending on the video source that is currently selected - REAR-SEL (white), AV1-SEL (yellow), NAVI-SEL (gray). For example, 12V output is on yellow wire when AV1 input source is chosen. Can be used to activate appropriate audio output.

LED

First LED lamp indicates that interface is on.

Second LED lamp indicates that AV sources connected work well.

Interface Connections

RGB interface board for W220 COMAND has a simple task to hijack COMAND video output when video input is received from RGB converter.

Installation

Remove the COMAND from the vehicle using COMAND removal instructions.

Unscrew 2 chassis cover screws at top of radio.

Unscrew 4 on the rear of the unit, remove cover from top of unit.

Begin by unscrewing the cassette player mechanism from the unit. There are 2 screws holding it in place.

Unscrew the mechanism's other mounting screw.

Loosen the ribbon cable attachment clip with a small screwdriver and carefully remove the cassette player mechanism.

Continue removing the remaining screws to remove the upper motherboard.

Using needle nosed pliers twist the metal clip that attaches to the upper motherboard.

Using a small screwdriver unscrew the ribbon cable from the motherboard.

Unclip the plastic connector from both sides.

Disconnect ribbon cable from the motherboard.

Leave the ribbon cable disconnected.

Connect ribbon cables as shown above.

Reattach the upper motherboard and cassette player mechanism.

Pull ribbon cables through the cassette player case.

Connect the RGB interface board.

Connect RGB cable and run outside of unit.

Mount converter on top of radio with 2 sided tape.